/*
- * (C) Copyright 2000-2002
+ * (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
# define SHOW_BOOT_PROGRESS(arg)
#endif
+#ifdef __PPC__
+# define EIEIO __asm__ volatile ("eieio")
+#else
+# define EIEIO /* nothing */
+#endif
#undef IDE_DEBUG
static int ide_bus_ok[CFG_IDE_MAXBUS] = {0,};
#endif
-static block_dev_desc_t ide_dev_desc[CFG_IDE_MAXDEVICE];
+block_dev_desc_t ide_dev_desc[CFG_IDE_MAXDEVICE];
/* ------------------------------------------------------------------------- */
#ifdef CONFIG_IDE_LED
-#if !defined(CONFIG_KUP4K) && !defined(CONFIG_HMI10)
+#if !defined(CONFIG_KUP4K) && !defined(CONFIG_KUP4X) &&!defined(CONFIG_BMS2003) &&!defined(CONFIG_CPC45)
static void ide_led (uchar led, uchar status);
#else
extern void ide_led (uchar led, uchar status);
if (strcmp(argv[1],"read") == 0) {
ulong addr = simple_strtoul(argv[2], NULL, 16);
-#if CFG_64BIT_STRTOUL
- lbaint_t blk = simple_strtoull(argv[3], NULL, 16);
-#else
- lbaint_t blk = simple_strtoul(argv[3], NULL, 16);
-#endif
ulong cnt = simple_strtoul(argv[4], NULL, 16);
ulong n;
+#ifdef CFG_64BIT_STRTOUL
+ lbaint_t blk = simple_strtoull(argv[3], NULL, 16);
printf ("\nIDE read: device %d block # %qd, count %ld ... ",
curr_device, blk, cnt);
+#else
+ lbaint_t blk = simple_strtoul(argv[3], NULL, 16);
+
+ printf ("\nIDE read: device %d block # %ld, count %ld ... ",
+ curr_device, blk, cnt);
+#endif
n = ide_dev_desc[curr_device].block_read (curr_device,
blk, cnt,
}
} else if (strcmp(argv[1],"write") == 0) {
ulong addr = simple_strtoul(argv[2], NULL, 16);
-#if CFG_64BIT_STRTOUL
- lbaint_t blk = simple_strtoull(argv[3], NULL, 16);
-#else
- lbaint_t blk = simple_strtoul(argv[3], NULL, 16);
-#endif
ulong cnt = simple_strtoul(argv[4], NULL, 16);
ulong n;
+#ifdef CFG_64BIT_STRTOUL
+ lbaint_t blk = simple_strtoull(argv[3], NULL, 16);
printf ("\nIDE write: device %d block # %qd, count %ld ... ",
curr_device, blk, cnt);
+#else
+ lbaint_t blk = simple_strtoul(argv[3], NULL, 16);
+
+ printf ("\nIDE write: device %d block # %ld, count %ld ... ",
+ curr_device, blk, cnt);
+#endif
n = ide_write (curr_device, blk, cnt, (ulong *)addr);
#endif /* CONFIG_IDE_8xx_PCCARD */
#ifdef CONFIG_IDE_PREINIT
+ extern int ide_preinit (void);
WATCHDOG_RESET();
if (ide_preinit ()) {
/* ------------------------------------------------------------------------- */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static void __inline__
ide_outb(int dev, int port, unsigned char val)
{
- PRINTF ("ide_outb (dev= %d, port= %d, val= 0x%02x) : @ 0x%08lx\n",
+ PRINTF ("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
dev, port, val, (ATA_CURR_BASE(dev)+port));
/* Ensure I/O operations complete */
- __asm__ volatile("eieio");
+ EIEIO;
*((uchar *)(ATA_CURR_BASE(dev)+port)) = val;
}
#else /* ! __PPC__ */
#endif /* __PPC__ */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static unsigned char __inline__
ide_inb(int dev, int port)
{
uchar val;
/* Ensure I/O operations complete */
- __asm__ volatile("eieio");
+ EIEIO;
val = *((uchar *)(ATA_CURR_BASE(dev)+port));
- PRINTF ("ide_inb (dev= %d, port= %d) : @ 0x%08lx -> 0x%02x\n",
+ PRINTF ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
dev, port, (ATA_CURR_BASE(dev)+port), val);
return (val);
}
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
}
if (words&1)
volatile ushort *pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
ushort *dbuf = (ushort *)sect_buf;
+ PRINTF("in input swap data base for read is %lx\n", (unsigned long) pbuf);
+
while (words--) {
*dbuf++ = ld_le16(pbuf);
*dbuf++ = ld_le16(pbuf);
#endif /* __LITTLE_ENDIAN || CONFIG_AU1X00 */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static void
output_data(int dev, ulong *sect_buf, int words)
{
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
}
#else /* CONFIG_HMI10 */
pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
dbuf = (uchar *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf_even = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf_odd = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf_even = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf_odd = *dbuf++;
}
#endif /* CONFIG_HMI10 */
}
#endif /* __PPC__ */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static void
input_data(int dev, ulong *sect_buf, int words)
{
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
+
+ PRINTF("in input data base for read is %lx\n", (unsigned long) pbuf);
+
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
}
#else /* CONFIG_HMI10 */
pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
dbuf = (uchar *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
+ EIEIO;
*dbuf++ = *pbuf_even;
- __asm__ volatile ("eieio");
+ EIEIO;
+ EIEIO;
*dbuf++ = *pbuf_odd;
- __asm__ volatile ("eieio");
+ EIEIO;
+ EIEIO;
*dbuf++ = *pbuf_even;
- __asm__ volatile ("eieio");
+ EIEIO;
+ EIEIO;
*dbuf++ = *pbuf_odd;
}
#endif /* CONFIG_HMI10 */
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
- __asm__ volatile ("eieio");
+ EIEIO;
}
if (words&1) {
#ifdef CONFIG_AMIGAONEG3SE
int max_bus_scan;
- int retries = 0;
char *s;
+#endif
+#ifdef CONFIG_ATAPI
+ int retries = 0;
int do_retry = 0;
#endif
dev_desc->if_type=IF_TYPE_IDE;
#ifdef CONFIG_ATAPI
-#ifdef CONFIG_AMIGAONEG3SE
do_retry = 0;
retries = 0;
/* Warning: This will be tricky to read */
while (retries <= 1) {
-#endif /* CONFIG_AMIGAONEG3SE */
-
/* check signature */
if ((ide_inb(device,ATA_SECT_CNT) == 0x01) &&
(ide_inb(device,ATA_SECT_NUM) == 0x01) &&
if (((c & ATA_STAT_DRQ) == 0) ||
((c & (ATA_STAT_FAULT|ATA_STAT_ERR)) != 0) ) {
+#ifdef CONFIG_ATAPI
#ifdef CONFIG_AMIGAONEG3SE
- if (retries == 0) {
- do_retry = 1;
- } else {
- return;
- }
-#else
- return;
-#endif /* CONFIG_AMIGAONEG3SE */
- }
-
-#ifdef CONFIG_AMIGAONEG3SE
- s = getenv("ide_doreset");
- if (s && strcmp(s, "on") == 0 && 1 == do_retry) {
- /* Need to soft reset the device in case it's an ATAPI... */
- PRINTF("Retrying...\n");
+ s = getenv("ide_doreset");
+ if (s && strcmp(s, "on") == 0)
+#endif
+ {
+ /* Need to soft reset the device in case it's an ATAPI... */
+ PRINTF("Retrying...\n");
+ ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
+ udelay(100000);
+ ide_outb (device, ATA_COMMAND, 0x08);
+ udelay (500000); /* 500 ms */
+ }
+ /* Select device
+ */
ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
- udelay(100000);
- ide_outb (device, ATA_COMMAND, 0x08);
- udelay (100000); /* 100 ms */
retries++;
- } else {
- retries = 100;
+#else
+ return;
+#endif
}
+#ifdef CONFIG_ATAPI
+ else
+ break;
} /* see above - ugly to read */
-#endif /* CONFIG_AMIGAONEG3SE */
+
+ if (retries == 2) /* Not found */
+ return;
+#endif
input_swap_data (device, iobuf, ATA_SECTORWORDS);
ident_cpy (dev_desc->revision, iop->fw_rev, sizeof(dev_desc->revision));
ident_cpy (dev_desc->vendor, iop->model, sizeof(dev_desc->vendor));
ident_cpy (dev_desc->product, iop->serial_no, sizeof(dev_desc->product));
+#ifdef __LITTLE_ENDIAN
+ /*
+ * firmware revision and model number have Big Endian Byte
+ * order in Word. Convert both to little endian.
+ *
+ * See CF+ and CompactFlash Specification Revision 2.0:
+ * 6.2.1.6: Identfy Drive, Table 39 for more details
+ */
+
+ strswab (dev_desc->revision);
+ strswab (dev_desc->vendor);
+#endif /* __LITTLE_ENDIAN */
if ((iop->config & 0x0080)==0x0080)
dev_desc->removable = 1;
}
#endif /* CONFIG_ATAPI */
+#ifdef __BIG_ENDIAN
/* swap shorts */
dev_desc->lba = (iop->lba_capacity << 16) | (iop->lba_capacity >> 16);
+#else /* ! __BIG_ENDIAN */
+ /*
+ * do not swap shorts on little endian
+ *
+ * See CF+ and CompactFlash Specification Revision 2.0:
+ * 6.2.1.6: Identfy Drive, Table 39, Word Address 57-58 for details.
+ */
+ dev_desc->lba = iop->lba_capacity;
+#endif /* __BIG_ENDIAN */
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
if (iop->command_set_2 & 0x0400) { /* LBA 48 support */
- dev_desc->lba48support = 1;
- dev_desc->lba48 = (unsigned long long)iop->lba48_capacity[0] |
+ dev_desc->lba48 = 1;
+ dev_desc->lba = (unsigned long long)iop->lba48_capacity[0] |
((unsigned long long)iop->lba48_capacity[1] << 16) |
((unsigned long long)iop->lba48_capacity[2] << 32) |
((unsigned long long)iop->lba48_capacity[3] << 48);
} else {
- dev_desc->lba48support = 0;
dev_desc->lba48 = 0;
}
#endif /* CONFIG_LBA48 */
ulong n = 0;
unsigned char c;
unsigned char pwrsave=0; /* power save */
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
unsigned char lba48 = 0;
if (blknr & 0x0000fffff0000000) {
printf ("IDE read: device %d not ready\n", device);
break;
}
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
if (lba48) {
/* write high bits */
ide_outb (device, ATA_SECT_CNT, 0);
ide_outb (device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
ide_outb (device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
if (lba48) {
ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device) );
ide_outb (device, ATA_COMMAND, ATA_CMD_READ_EXT);
}
if ((c&(ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR)) != ATA_STAT_DRQ) {
-#if CFG_64BIT_LBA && CFG_64BIT_VSPRINTF
+#if defined(CFG_64BIT_LBA) && defined(CFG_64BIT_VSPRINTF)
printf ("Error (no IRQ) dev %d blk %qd: status 0x%02x\n",
device, blknr, c);
#else
{
ulong n = 0;
unsigned char c;
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
unsigned char lba48 = 0;
if (blknr & 0x0000fffff0000000) {
printf ("IDE read: device %d not ready\n", device);
goto WR_OUT;
}
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
if (lba48) {
/* write high bits */
ide_outb (device, ATA_SECT_CNT, 0);
ide_outb (device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
ide_outb (device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
-#if CONFIG_LBA48
+#ifdef CONFIG_LBA48
if (lba48) {
ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device) );
ide_outb (device, ATA_COMMAND, ATA_CMD_WRITE_EXT);
c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
if ((c&(ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR)) != ATA_STAT_DRQ) {
-#if CFG_64BIT_LBA && CFG_64BIT_VSPRINTF
+#if defined(CFG_64BIT_LBA) && defined(CFG_64BIT_VSPRINTF)
printf ("Error (no IRQ) dev %d blk %qd: status 0x%02x\n",
device, blknr, c);
#else
/*
* copy src to dest, skipping leading and trailing blanks and null
* terminate the string
+ * "len" is the size of available memory including the terminating '\0'
*/
-static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len)
+static void ident_cpy (unsigned char *dst, unsigned char *src, unsigned int len)
{
- int start,end;
+ unsigned char *end, *last;
- start=0;
- while (start<len) {
- if (src[start]!=' ')
- break;
- start++;
- }
- end=len-1;
- while (end>start) {
- if (src[end]!=' ')
- break;
- end--;
- }
- for ( ; start<=end; start++) {
- *dest++=src[start];
+ last = dst;
+ end = src + len - 1;
+
+ /* reserve space for '\0' */
+ if (len < 2)
+ goto OUT;
+
+ /* skip leading white space */
+ while ((*src) && (src<end) && (*src==' '))
+ ++src;
+
+ /* copy string, omitting trailing white space */
+ while ((*src) && (src<end)) {
+ *dst++ = *src;
+ if (*src++ != ' ')
+ last = dst;
}
- *dest='\0';
+OUT:
+ *last = '\0';
}
/* ------------------------------------------------------------------------- */
/* ------------------------------------------------------------------------- */
-#if defined(CONFIG_IDE_LED) && !defined(CONFIG_AMIGAONEG3SE) && !defined(CONFIG_KUP4K) && !defined(CONFIG_HMI10)
+#if defined(CONFIG_IDE_LED) && \
+ !defined(CONFIG_AMIGAONEG3SE)&& \
+ !defined(CONFIG_CPC45) && \
+ !defined(CONFIG_HMI10) && \
+ !defined(CONFIG_KUP4K) && \
+ !defined(CONFIG_KUP4X)
static uchar led_buffer = 0; /* Buffer for current LED status */
* ATAPI Support
*/
-
#undef ATAPI_DEBUG
#ifdef ATAPI_DEBUG
#define AT_PRINTF(fmt,args...)
#endif
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
/* since ATAPI may use commands with not 4 bytes alligned length
* we have our own transfer functions, 2 bytes alligned */
static void
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
+
+ PRINTF("in output data shorts base for read is %lx\n", (unsigned long) pbuf);
+
while (shorts--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
}
#else /* CONFIG_HMI10 */
pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
while (shorts--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf_even = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf_odd = *dbuf++;
}
#endif /* CONFIG_HMI10 */
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
+
+ PRINTF("in input data shorts base for read is %lx\n", (unsigned long) pbuf);
+
while (shorts--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
}
#else /* CONFIG_HMI10 */
pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
while (shorts--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf_even;
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf_odd;
}
#endif /* CONFIG_HMI10 */
outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts);
}
-
static void
input_data_shorts(int dev, ushort *sect_buf, int shorts)
{
((unsigned long)iobuf[5]<<16) +
((unsigned long)iobuf[6]<< 8) +
((unsigned long)iobuf[7]);
+#ifdef CONFIG_LBA48
dev_desc->lba48 = 0; /* ATAPI devices cannot use 48bit addressing (ATA/ATAPI v7) */
+#endif
return;
}
projects / u-boot / blobdiff