if SPL
+config SPL_LDSCRIPT
+ string "Linker script for the SPL stage"
+ default "arch/$(ARCH)/cpu/u-boot-spl.lds"
+ depends on SPL
+ help
+ The SPL stage will usually require a different linker-script
+ (as it runs from a different memory region) than the regular
+ U-Boot stage. Set this to the path of the linker-script to
+ be used for SPL.
+
config SPL_BOARD_INIT
bool "Call board-specific initialization in SPL"
help
spl_board_init() from board_init_r(). This function should be
provided by the board.
+config SPL_BOOTROM_SUPPORT
+ bool "Support returning to the BOOTROM"
+ help
+ Some platforms (e.g. the Rockchip RK3368) provide support in their
+ ROM for loading the next boot-stage after performing basic setup
+ from the SPL stage.
+
+ Enable this option, to return to the BOOTROM through the
+ BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
+ boot device list, if not implemented for a given board)
+
config SPL_RAW_IMAGE_SUPPORT
bool "Support SPL loading and booting of RAW images"
default n if (ARCH_MX6 && (SPL_MMC_SUPPORT || SPL_SATA_SUPPORT))
this will make the SPL binary smaller at the cost of more heap
usage as the *_simple malloc functions do not re-use free-ed mem.
+config TPL_SYS_MALLOC_SIMPLE
+ bool
+ prompt "Only use malloc_simple functions in the TPL"
+ help
+ Say Y here to only use the *_simple malloc functions from
+ malloc_simple.c, rather then using the versions from dlmalloc.c;
+ this will make the TPL binary smaller at the cost of more heap
+ usage as the *_simple malloc functions do not re-use free-ed mem.
+
config SPL_STACK_R
bool "Enable SDRAM location for SPL stack"
help
needed in SPL as it has a much simpler task with less
configuration. But some boards use this to support 'Falcon' boot
on EXT2 and FAT, where SPL boots directly into Linux without
- starting U-Boot first. Enabling this option will make getenv()
- and setenv() available in SPL.
+ starting U-Boot first. Enabling this option will make env_get()
+ and env_set() available in SPL.
config SPL_SAVEENV
bool "Support save environment"
enable SPI drivers that are needed for other purposes also, such
as a SPI PMIC.
-config SPL_TIMER_SUPPORT
- bool "Support timer drivers"
- help
- Enable support for timer drivers in SPL. These can be used to get
- a timer value when in SPL, or perhaps for implementing a delay
- function. This enables the drivers in drivers/timer as part of an
- SPL build.
-
config SPL_USB_HOST_SUPPORT
bool "Support USB host drivers"
help
if TPL
+config TPL_LDSCRIPT
+ string "Linker script for the TPL stage"
+ depends on TPL
+ help
+ The TPL stage will usually require a different linker-script
+ (as it runs from a different memory region) than the regular
+ U-Boot stage. Set this to the path of the linker-script to
+ be used for TPL.
+
+ May be left empty to trigger the Makefile infrastructure to
+ fall back to the linker-script used for the SPL stage.
+
+config TPL_NEEDS_SEPARATE_TEXT_BASE
+ bool "TPL needs a separate text-base"
+ default n
+ depends on TPL
+ help
+ Enable, if the TPL stage should not inherit its text-base
+ from the SPL stage. When enabled, a base address for the
+ .text sections of the TPL stage has to be set below.
+
+config TPL_NEEDS_SEPARATE_STACK
+ bool "TPL needs a separate initial stack-pointer"
+ default n
+ depends on TPL
+ help
+ Enable, if the TPL stage should not inherit its initial
+ stack-pointer from the settings for the SPL stage.
+
+config TPL_TEXT_BASE
+ hex "Base address for the .text section of the TPL stage"
+ depends on TPL_NEEDS_SEPARATE_TEXT_BASE
+ help
+ The base address for the .text section of the TPL stage.
+
+config TPL_MAX_SIZE
+ int "Maximum size (in bytes) for the TPL stage"
+ default 0
+ depends on TPL
+ help
+ The maximum size (in bytes) of the TPL stage.
+
+config TPL_STACK
+ hex "Address of the initial stack-pointer for the TPL stage"
+ depends on TPL_NEEDS_SEPARATE_STACK
+ help
+ The address of the initial stack-pointer for the TPL stage.
+ Usually this will be the (aligned) top-of-stack.
+
+config TPL_BOOTROM_SUPPORT
+ bool "Support returning to the BOOTROM (from TPL)"
+ help
+ Some platforms (e.g. the Rockchip RK3368) provide support in their
+ ROM for loading the next boot-stage after performing basic setup
+ from the TPL stage.
+
+ Enable this option, to return to the BOOTROM through the
+ BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
+ boot device list, if not implemented for a given board)
+
+config TPL_DRIVERS_MISC_SUPPORT
+ bool "Support misc drivers in TPL"
+ help
+ Enable miscellaneous drivers in TPL. These drivers perform various
+ tasks that don't fall nicely into other categories, Enable this
+ option to build the drivers in drivers/misc as part of an TPL
+ build, for those that support building in TPL (not all drivers do).
+
config TPL_ENV_SUPPORT
bool "Support an environment"
help
config TPL_I2C_SUPPORT
bool "Support I2C"
help
- Enable support for the I2C bus in SPL. See SPL_I2C_SUPPORT for
+ Enable support for the I2C bus in TPL. See SPL_I2C_SUPPORT for
details.
config TPL_LIBCOMMON_SUPPORT
config TPL_NAND_SUPPORT
bool "Support NAND flash"
help
- Enable support for NAND in SPL. See SPL_NAND_SUPPORT for details.
+ Enable support for NAND in TPL. See SPL_NAND_SUPPORT for details.
config TPL_SERIAL_SUPPORT
bool "Support serial"
help
- Enable support for serial in SPL. See SPL_SERIAL_SUPPORT for
+ Enable support for serial in TPL. See SPL_SERIAL_SUPPORT for
details.
config TPL_SPI_FLASH_SUPPORT
bool "Support SPI flash drivers"
help
- Enable support for using SPI flash in SPL. See SPL_SPI_FLASH_SUPPORT
+ Enable support for using SPI flash in TPL. See SPL_SPI_FLASH_SUPPORT
for details.
config TPL_SPI_SUPPORT
bool "Support SPI drivers"
help
- Enable support for using SPI in SPL. See SPL_SPI_SUPPORT for
+ Enable support for using SPI in TPL. See SPL_SPI_SUPPORT for
details.
endif # TPL
projects / u-boot / blobdiff