* (C) Copyright 2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright (C) 2004-2006 Freescale Semiconductor, Inc.
* (C) Copyright 2003 Motorola Inc.
* Xianghua Xiao (X.Xiao@motorola.com)
*
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
- *
- * Change log:
- *
- * 20050101: Eran Liberty (liberty@freescale.com)
- * Initial file creating (porting from 85XX & 8260)
- * 20060601: Dave Liu (daveliu@freescale.com)
- * DDR ECC support
- * unify variable names for 83xx
- * code cleanup
*/
#include <common.h>
#ifdef CONFIG_SPD_EEPROM
+DECLARE_GLOBAL_DATA_PTR;
+
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
extern void dma_init(void);
extern uint dma_check(void);
/*
* Convert picoseconds into clock cycles (rounding up if needed).
*/
-extern ulong get_ddr_clk(ulong dummy);
-
int
picos_to_clk(int picos)
{
unsigned int ddr_bus_clk;
int clks;
- ddr_bus_clk = get_ddr_clk(0) >> 1;
+ ddr_bus_clk = gd->ddr_clk >> 1;
clks = picos / ((1000000000 / ddr_bus_clk) * 1000);
- if (picos % ((1000000000 / ddr_bus_clk) * 1000) !=0) {
+ if (picos % ((1000000000 / ddr_bus_clk) * 1000) != 0)
clks++;
- }
return clks;
}
long int spd_sdram()
{
- volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ddr83xx_t *ddr = &immap->ddr;
volatile law83xx_t *ecm = &immap->sysconf.ddrlaw[0];
spd_eeprom_t spd;
- unsigned tmp;
unsigned int memsize;
unsigned int law_size;
unsigned char caslat, caslat_ctrl;
unsigned sdram_cfg;
unsigned int ddrc_ecc_enable;
-
- /* Read SPD parameters with I2C */
+ /* Read SPD parameters with I2C */
CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) & spd, sizeof (spd));
#ifdef SPD_DEBUG
spd_debug(&spd);
spd.ncol_addr);
return 0;
}
- /* Setup DDR chip select register */
+ /* Setup DDR chip select register */
+#ifdef CFG_83XX_DDR_USES_CS0
+ ddr->csbnds[0].csbnds = (banksize(spd.row_dens) >> 24) - 1;
+ ddr->cs_config[0] = ( 1 << 31
+ | (spd.nrow_addr - 12) << 8
+ | (spd.ncol_addr - 8) );
+ debug("\n");
+ debug("cs0_bnds = 0x%08x\n",ddr->csbnds[0].csbnds);
+ debug("cs0_config = 0x%08x\n",ddr->cs_config[0]);
+
+ if (spd.nrows == 2) {
+ ddr->csbnds[1].csbnds = ( (banksize(spd.row_dens) >> 8)
+ | ((banksize(spd.row_dens) >> 23) - 1) );
+ ddr->cs_config[1] = ( 1<<31
+ | (spd.nrow_addr-12) << 8
+ | (spd.ncol_addr-8) );
+ debug("cs1_bnds = 0x%08x\n",ddr->csbnds[1].csbnds);
+ debug("cs1_config = 0x%08x\n",ddr->cs_config[1]);
+ }
+
+#else
ddr->csbnds[2].csbnds = (banksize(spd.row_dens) >> 24) - 1;
ddr->cs_config[2] = ( 1 << 31
| (spd.nrow_addr - 12) << 8
debug("cs3_bnds = 0x%08x\n",ddr->csbnds[3].csbnds);
debug("cs3_config = 0x%08x\n",ddr->cs_config[3]);
}
+#endif
if (spd.mem_type != 0x07) {
puts("No DDR module found!\n");
* CAS Lat DDR I Ctrl
* Clocks SPD Bit Value
* -------+--------+---------
- * 1.0 0 001
- * 1.5 1 010
- * 2.0 2 011
- * 2.5 3 100
- * 3.0 4 101
- * 3.5 5 110
- * 4.0 6 111
+ * 1.0 0 001
+ * 1.5 1 010
+ * 2.0 2 011
+ * 2.5 3 100
+ * 3.0 4 101
+ * 3.5 5 110
+ * 4.0 6 111
*/
caslat = __ilog2(spd.cas_lat);
- if (caslat > 4 ) {
- printf("DDR: Invalid SPD CAS Latency, caslat=%02X\n", caslat);
+ if (caslat > 6 ) {
+ printf("DDR: Invalid SPD CAS Latency, caslat=%02X\n",
+ spd.cas_lat);
return 0;
}
max_bus_clk = 1000 *10 / (((spd.clk_cycle & 0xF0) >> 4) * 10
debug("DDR:Module maximum data rate is: %dMhz\n", max_data_rate);
- ddrc_clk = get_ddr_clk(0) / 1000000;
+ ddrc_clk = gd->ddr_clk / 1000000;
if (max_data_rate >= 390) { /* it is DDR 400 */
- printf("DDR: platform not support DDR 400\n");
- return 0;
+ if (ddrc_clk <= 410 && ddrc_clk > 350) {
+ /* DDR controller clk at 350~410 */
+ effective_data_rate = 400; /* 5ns */
+ caslat = caslat;
+ } else if (ddrc_clk <= 350 && ddrc_clk > 280) {
+ /* DDR controller clk at 280~350 */
+ effective_data_rate = 333; /* 6ns */
+ if (spd.clk_cycle2 == 0x60)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ } else if (ddrc_clk <= 280 && ddrc_clk > 230) {
+ /* DDR controller clk at 230~280 */
+ effective_data_rate = 266; /* 7.5ns */
+ if (spd.clk_cycle3 == 0x75)
+ caslat = caslat - 2;
+ else if (spd.clk_cycle2 == 0x60)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ } else if (ddrc_clk <= 230 && ddrc_clk > 90) {
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ if (spd.clk_cycle3 == 0x75)
+ caslat = caslat - 2;
+ else if (spd.clk_cycle2 == 0x60)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ }
} else if (max_data_rate >= 323) { /* it is DDR 333 */
if (ddrc_clk <= 350 && ddrc_clk > 280) {
- /* DDRC clk at 280~350 */
+ /* DDR controller clk at 280~350 */
effective_data_rate = 333; /* 6ns */
caslat = caslat;
} else if (ddrc_clk <= 280 && ddrc_clk > 230) {
- /* DDRC clk at 230~280 */
- if (spd.clk_cycle2 == 0x75) {
- effective_data_rate = 266; /* 7.5ns */
+ /* DDR controller clk at 230~280 */
+ effective_data_rate = 266; /* 7.5ns */
+ if (spd.clk_cycle2 == 0x75)
caslat = caslat - 1;
- }
+ else
+ caslat = caslat;
} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
- /* DDRC clk at 90~230 */
- if (spd.clk_cycle3 == 0xa0) {
- effective_data_rate = 200; /* 10ns */
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ if (spd.clk_cycle3 == 0xa0)
caslat = caslat - 2;
- }
+ else if (spd.clk_cycle2 == 0x75)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
}
} else if (max_data_rate >= 256) { /* it is DDR 266 */
if (ddrc_clk <= 350 && ddrc_clk > 280) {
- /* DDRC clk at 280~350 */
+ /* DDR controller clk at 280~350 */
printf("DDR: DDR controller freq is more than "
"max data rate of the module\n");
return 0;
} else if (ddrc_clk <= 280 && ddrc_clk > 230) {
- /* DDRC clk at 230~280 */
+ /* DDR controller clk at 230~280 */
effective_data_rate = 266; /* 7.5ns */
caslat = caslat;
} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
- /* DDRC clk at 90~230 */
- if (spd.clk_cycle2 == 0xa0) {
- effective_data_rate = 200; /* 10ns */
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ if (spd.clk_cycle2 == 0xa0)
caslat = caslat - 1;
- }
}
} else if (max_data_rate >= 190) { /* it is DDR 200 */
if (ddrc_clk <= 350 && ddrc_clk > 230) {
- /* DDRC clk at 230~350 */
+ /* DDR controller clk at 230~350 */
printf("DDR: DDR controller freq is more than "
"max data rate of the module\n");
return 0;
} else if (ddrc_clk <= 230 && ddrc_clk > 90) {
- /* DDRC clk at 90~230 */
+ /* DDR controller clk at 90~230 */
effective_data_rate = 200; /* 10ns */
caslat = caslat;
}
}
+ debug("DDR:Effective data rate is: %dMhz\n", effective_data_rate);
+ debug("DDR:The MSB 1 of CAS Latency is: %d\n", caslat);
+
+ /*
+ * Errata DDR6 work around: input enable 2 cycles earlier.
+ * including MPC834x Rev1.0/1.1 and MPC8360 Rev1.1/1.2.
+ */
+ if (caslat == 2)
+ ddr->debug_reg = 0x201c0000; /* CL=2 */
+ else if (caslat == 3)
+ ddr->debug_reg = 0x202c0000; /* CL=2.5 */
+ else if (caslat == 4)
+ ddr->debug_reg = 0x202c0000; /* CL=3.0 */
+
+ __asm__ __volatile__ ("sync");
+
+ debug("Errata DDR6 (debug_reg=0x%08x)\n", ddr->debug_reg);
+
/*
* note: caslat must also be programmed into ddr->sdram_mode
* register.
ddr->sdram_cfg = 0x42000000;
/* Check DIMM data bus width */
- if (spd.dataw_lsb == 0x20)
- {
+ if (spd.dataw_lsb == 0x20) {
burstlen = 0x03; /* 32 bit data bus, burst len is 8 */
printf("\n DDR DIMM: data bus width is 32 bit");
- }
- else
- {
+ } else {
burstlen = 0x02; /* Others act as 64 bit bus, burst len is 4 */
printf("\n DDR DIMM: data bus width is 64 bit");
}
/* Is this an ECC DDR chip? */
- if (spd.config == 0x02) {
+ if (spd.config == 0x02)
printf(" with ECC\n");
- }
else
printf(" without ECC\n");
/* Burst length is always 4 for 64 bit data bus, 8 for 32 bit data bus,
Burst type is sequential
*/
- switch(caslat) {
- case 1:
- ddr->sdram_mode = 0x50 | burstlen; /* CL=1.5 */
- break;
- case 2:
- ddr->sdram_mode = 0x20 | burstlen; /* CL=2.0 */
- break;
- case 3:
- ddr->sdram_mode = 0x60 | burstlen; /* CL=2.5 */
- break;
- case 4:
- ddr->sdram_mode = 0x30 | burstlen; /* CL=3.0 */
- break;
- default:
- printf("DDR:only CAS Latency 1.5, 2.0, 2.5, 3.0 "
- "is supported.\n");
- return 0;
+ switch (caslat) {
+ case 1:
+ ddr->sdram_mode = 0x50 | burstlen; /* CL=1.5 */
+ break;
+ case 2:
+ ddr->sdram_mode = 0x20 | burstlen; /* CL=2.0 */
+ break;
+ case 3:
+ ddr->sdram_mode = 0x60 | burstlen; /* CL=2.5 */
+ break;
+ case 4:
+ ddr->sdram_mode = 0x30 | burstlen; /* CL=3.0 */
+ break;
+ default:
+ printf("DDR:only CL 1.5, 2.0, 2.5, 3.0 is supported\n");
+ return 0;
}
debug("DDR:sdram_mode=0x%08x\n", ddr->sdram_mode);
- switch(spd.refresh) {
- case 0x00:
- case 0x80:
- tmp = picos_to_clk(15625000);
- break;
- case 0x01:
- case 0x81:
- tmp = picos_to_clk(3900000);
- break;
- case 0x02:
- case 0x82:
- tmp = picos_to_clk(7800000);
- break;
- case 0x03:
- case 0x83:
- tmp = picos_to_clk(31300000);
- break;
- case 0x04:
- case 0x84:
- tmp = picos_to_clk(62500000);
- break;
- case 0x05:
- case 0x85:
- tmp = picos_to_clk(125000000);
- break;
- default:
- tmp = 0x512;
- break;
+ switch (spd.refresh) {
+ case 0x00:
+ case 0x80:
+ refresh_clk = picos_to_clk(15625000);
+ break;
+ case 0x01:
+ case 0x81:
+ refresh_clk = picos_to_clk(3900000);
+ break;
+ case 0x02:
+ case 0x82:
+ refresh_clk = picos_to_clk(7800000);
+ break;
+ case 0x03:
+ case 0x83:
+ refresh_clk = picos_to_clk(31300000);
+ break;
+ case 0x04:
+ case 0x84:
+ refresh_clk = picos_to_clk(62500000);
+ break;
+ case 0x05:
+ case 0x85:
+ refresh_clk = picos_to_clk(125000000);
+ break;
+ default:
+ refresh_clk = 0x512;
+ break;
}
/*
* Set BSTOPRE to 0x100 for page mode
* If auto-charge is used, set BSTOPRE = 0
*/
- ddr->sdram_interval = ((tmp & 0x3fff) << 16) | 0x100;
+ ddr->sdram_interval = ((refresh_clk & 0x3fff) << 16) | 0x100;
debug("DDR:sdram_interval=0x%08x\n", ddr->sdram_interval);
/* SS_EN = 0, source synchronous disable
* CLK_ADJST = 0, MCK/MCK# is launched aligned with addr/cmd
- */
+ */
ddr->sdram_clk_cntl = 0x00000000;
debug("DDR:sdram_clk_cntl=0x%08x\n", ddr->sdram_clk_cntl);
udelay(600);
/*
- * Figure out the settings for the sdram_cfg register. Build up
- * the entire register in 'tmp' before writing since the write into
+ * Figure out the settings for the sdram_cfg register. Build up
+ * the value in 'sdram_cfg' before writing since the write into
* the register will actually enable the memory controller, and all
* settings must be done before enabling.
*
sdram_cfg = 0xC2000000;
/* sdram_cfg[3] = RD_EN - registered DIMM enable */
- if (spd.mod_attr & 0x02) {
+ if (spd.mod_attr & 0x02)
sdram_cfg |= 0x10000000;
- }
/* The DIMM is 32bit width */
- if (spd.dataw_lsb == 0x20) {
+ if (spd.dataw_lsb == 0x20)
sdram_cfg |= 0x000C0000;
- }
+
ddrc_ecc_enable = 0;
#if defined(CONFIG_DDR_ECC)
/* set single bit error threshold to maximum value,
* reset counter to zero */
ddr->err_sbe = (255 << ECC_ERROR_MAN_SBET_SHIFT) |
- (0 << ECC_ERROR_MAN_SBEC_SHIFT);
+ (0 << ECC_ERROR_MAN_SBEC_SHIFT);
}
debug("DDR:err_disable=0x%08x\n", ddr->err_disable);
debug("DDR:err_sbe=0x%08x\n", ddr->err_sbe);
#endif
- printf(" DDRC ECC mode: %s", ddrc_ecc_enable ? "ON":"OFF");
+ printf(" DDRC ECC mode: %s\n", ddrc_ecc_enable ? "ON":"OFF");
#if defined(CONFIG_DDR_2T_TIMING)
/*
}
#endif /* CONFIG_SPD_EEPROM */
-
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
/*
* Use timebase counter, get_timer() is not availabe
/* #define CONFIG_DDR_ECC_INIT_VIA_DMA */
void ddr_enable_ecc(unsigned int dram_size)
{
- uint *p;
- volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ddr83xx_t *ddr= &immap->ddr;
unsigned long t_start, t_end;
+ register u64 *p;
+ register uint size;
+ unsigned int pattern[2];
#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
uint i;
#endif
-
- debug("Initialize a Cachline in DRAM\n");
icache_enable();
-
-#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
- /* Initialise DMA for direct Transfers */
- dma_init();
-#endif
-
t_start = get_tbms();
+ pattern[0] = 0xdeadbeef;
+ pattern[1] = 0xdeadbeef;
#if !defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
- debug("DDR init: Cache flush method\n");
- for (p = 0; p < (uint *)(dram_size); p++) {
- if (((unsigned int)p & 0x1f) == 0) {
- ppcDcbz((unsigned long) p);
- }
-
- /* write pattern to cache and flush */
- *p = (unsigned int)0xdeadbeef;
-
- if (((unsigned int)p & 0x1c) == 0x1c) {
- ppcDcbf((unsigned long) p);
- }
+ debug("ddr init: CPU FP write method\n");
+ size = dram_size;
+ for (p = 0; p < (u64*)(size); p++) {
+ ppcDWstore((u32*)p, pattern);
}
+ __asm__ __volatile__ ("sync");
#else
- printf("DDR init: DMA method\n");
- for (p = 0; p < (uint *)(8 * 1024); p++) {
- /* zero one data cache line */
- if (((unsigned int)p & 0x1f) == 0) {
- ppcDcbz((unsigned long)p);
- }
-
- /* write pattern to it and flush */
- *p = (unsigned int)0xdeadbeef;
-
- if (((unsigned int)p & 0x1c) == 0x1c) {
- ppcDcbf((unsigned long)p);
- }
+ debug("ddr init: DMA method\n");
+ size = 0x2000;
+ for (p = 0; p < (u64*)(size); p++) {
+ ppcDWstore((u32*)p, pattern);
}
+ __asm__ __volatile__ ("sync");
- /* 8K */
- dma_xfer((uint *)0x2000, 0x2000, (uint *)0);
- /* 16K */
- dma_xfer((uint *)0x4000, 0x4000, (uint *)0);
- /* 32K */
- dma_xfer((uint *)0x8000, 0x8000, (uint *)0);
- /* 64K */
- dma_xfer((uint *)0x10000, 0x10000, (uint *)0);
- /* 128k */
- dma_xfer((uint *)0x20000, 0x20000, (uint *)0);
- /* 256k */
- dma_xfer((uint *)0x40000, 0x40000, (uint *)0);
- /* 512k */
- dma_xfer((uint *)0x80000, 0x80000, (uint *)0);
- /* 1M */
- dma_xfer((uint *)0x100000, 0x100000, (uint *)0);
- /* 2M */
- dma_xfer((uint *)0x200000, 0x200000, (uint *)0);
- /* 4M */
- dma_xfer((uint *)0x400000, 0x400000, (uint *)0);
+ /* Initialise DMA for direct transfer */
+ dma_init();
+ /* Start DMA to transfer */
+ dma_xfer((uint *)0x2000, 0x2000, (uint *)0); /* 8K */
+ dma_xfer((uint *)0x4000, 0x4000, (uint *)0); /* 16K */
+ dma_xfer((uint *)0x8000, 0x8000, (uint *)0); /* 32K */
+ dma_xfer((uint *)0x10000, 0x10000, (uint *)0); /* 64K */
+ dma_xfer((uint *)0x20000, 0x20000, (uint *)0); /* 128K */
+ dma_xfer((uint *)0x40000, 0x40000, (uint *)0); /* 256K */
+ dma_xfer((uint *)0x80000, 0x80000, (uint *)0); /* 512K */
+ dma_xfer((uint *)0x100000, 0x100000, (uint *)0); /* 1M */
+ dma_xfer((uint *)0x200000, 0x200000, (uint *)0); /* 2M */
+ dma_xfer((uint *)0x400000, 0x400000, (uint *)0); /* 4M */
for (i = 1; i < dram_size / 0x800000; i++) {
dma_xfer((uint *)(0x800000*i), 0x800000, (uint *)0);