#include <common.h>
#include <ppc_asm.tmpl>
#include <asm/processor.h>
+#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
void get_sys_info (sys_info_t * sysInfo)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
uint plat_ratio,e500_ratio,half_freqSystemBus;
+ uint lcrr_div;
plat_ratio = (gur->porpllsr) & 0x0000003e;
plat_ratio >>= 1;
* overflow for processor speeds above 2GHz */
half_freqSystemBus = sysInfo->freqSystemBus/2;
sysInfo->freqProcessor = e500_ratio*half_freqSystemBus;
+
+ /* Note: freqDDRBus is the MCLK frequency, not the data rate. */
+ sysInfo->freqDDRBus = sysInfo->freqSystemBus;
+
+#ifdef CONFIG_DDR_CLK_FREQ
+ {
+ u32 ddr_ratio = ((gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO)
+ >> MPC85xx_PORPLLSR_DDR_RATIO_SHIFT;
+ if (ddr_ratio != 0x7)
+ sysInfo->freqDDRBus = ddr_ratio * CONFIG_DDR_CLK_FREQ;
+ }
+#endif
+
+#if defined(CONFIG_SYS_LBC_LCRR)
+ /* We will program LCRR to this value later */
+ lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV;
+#else
+ {
+ volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV;
+ }
+#endif
+ if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) {
+#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8541) && \
+ !defined(CONFIG_MPC8555) && !defined(CONFIG_MPC8560)
+ /*
+ * Yes, the entire PQ38 family use the same
+ * bit-representation for twice the clock divider values.
+ */
+ lcrr_div *= 2;
+#endif
+ sysInfo->freqLocalBus = sysInfo->freqSystemBus / lcrr_div;
+ } else {
+ /* In case anyone cares what the unknown value is */
+ sysInfo->freqLocalBus = lcrr_div;
+ }
}
int get_clocks (void)
{
sys_info_t sys_info;
+#ifdef CONFIG_MPC8544
+ volatile ccsr_gur_t *gur = (void *) CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#endif
#if defined(CONFIG_CPM2)
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR;
uint sccr, dfbrg;
/* set VCO = 4 * BRG */
- immap->im_cpm.im_cpm_intctl.sccr &= 0xfffffffc;
- sccr = immap->im_cpm.im_cpm_intctl.sccr;
+ cpm->im_cpm_intctl.sccr &= 0xfffffffc;
+ sccr = cpm->im_cpm_intctl.sccr;
dfbrg = (sccr & SCCR_DFBRG_MSK) >> SCCR_DFBRG_SHIFT;
#endif
get_sys_info (&sys_info);
gd->cpu_clk = sys_info.freqProcessor;
gd->bus_clk = sys_info.freqSystemBus;
+ gd->mem_clk = sys_info.freqDDRBus;
+ gd->lbc_clk = sys_info.freqLocalBus;
+
+ /*
+ * The base clock for I2C depends on the actual SOC. Unfortunately,
+ * there is no pattern that can be used to determine the frequency, so
+ * the only choice is to look up the actual SOC number and use the value
+ * for that SOC. This information is taken from application note
+ * AN2919.
+ */
+#if defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
+ defined(CONFIG_MPC8560) || defined(CONFIG_MPC8555)
+ gd->i2c1_clk = sys_info.freqSystemBus;
+#elif defined(CONFIG_MPC8544)
+ /*
+ * On the 8544, the I2C clock is the same as the SEC clock. This can be
+ * either CCB/2 or CCB/3, depending on the value of cfg_sec_freq. See
+ * 4.4.3.3 of the 8544 RM. Note that this might actually work for all
+ * 85xx, but only the 8544 has cfg_sec_freq, so it's unknown if the
+ * PORDEVSR2_SEC_CFG bit is 0 on all 85xx boards that are not an 8544.
+ */
+ if (gur->pordevsr2 & MPC85xx_PORDEVSR2_SEC_CFG)
+ gd->i2c1_clk = sys_info.freqSystemBus / 3;
+ else
+ gd->i2c1_clk = sys_info.freqSystemBus / 2;
+#else
+ /* Most 85xx SOCs use CCB/2, so this is the default behavior. */
+ gd->i2c1_clk = sys_info.freqSystemBus / 2;
+#endif
+ gd->i2c2_clk = gd->i2c1_clk;
+
+#if defined(CONFIG_MPC8536)
+ gd->sdhc_clk = gd->bus_clk / 2;
+#endif
+
#if defined(CONFIG_CPM2)
gd->vco_out = 2*sys_info.freqSystemBus;
gd->cpm_clk = gd->vco_out / 2;
*********************************************/
ulong get_bus_freq (ulong dummy)
{
- ulong val;
-
- sys_info_t sys_info;
-
- get_sys_info (&sys_info);
- val = sys_info.freqSystemBus;
+ return gd->bus_clk;
+}
- return val;
+/********************************************
+ * get_ddr_freq
+ * return ddr bus freq in Hz
+ *********************************************/
+ulong get_ddr_freq (ulong dummy)
+{
+ return gd->mem_clk;
}