CONFIG_M5373EVB -- define for M5373EVB board
CONFIG_MCFUART -- define to use common CF Uart driver
-CFG_UART_PORT -- define UART port number, start with 0, 1 and 2
+CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
CONFIG_BAUDRATE -- define UART baudrate
CONFIG_MCFRTC -- define to use common CF RTC driver
-CFG_MCFRTC_BASE -- provide base address for RTC in immap.h
-CFG_RTC_OSCILLATOR -- define RTC clock frequency
+CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h
+CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency
RTC_DEBUG -- define to show RTC debug message
CONFIG_CMD_DATE -- enable to use date feature in u-boot
CONFIG_NET_MULTI -- define to use multi FEC in u-boot
CONFIG_MII -- enable to use MII driver
CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c
-CFG_DISCOVER_PHY -- enable PHY discovery
-CFG_RX_ETH_BUFFER -- Set FEC Receive buffer
-CFG_FAULT_ECHO_LINK_DOWN--
-CFG_FEC0_PINMUX -- Set FEC0 Pin configuration
-CFG_FEC0_MIIBASE -- Set FEC0 MII base register
+CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery
+CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
+CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration
+CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register
MCFFEC_TOUT_LOOP -- set FEC timeout loop
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_FSL_I2C -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SOFT_I2C -- define for I2C bit-banged
-CFG_I2C_SPEED -- define for I2C speed
-CFG_I2C_SLAVE -- define for I2C slave address
-CFG_I2C_OFFSET -- define for I2C base address offset
-CFG_IMMR -- define for MBAR offset
+CONFIG_SYS_I2C_SPEED -- define for I2C speed
+CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
+CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset
+CONFIG_SYS_IMMR -- define for MBAR offset
-CFG_MBAR -- define MBAR offset
+CONFIG_SYS_MBAR -- define MBAR offset
CONFIG_MONITOR_IS_IN_RAM -- Not support
-CFG_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
+CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
-CFG_CSn_BASE -- defines the Chip Select Base register
-CFG_CSn_MASK -- defines the Chip Select Mask register
-CFG_CSn_CTRL -- defines the Chip Select Control register
+CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register
+CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register
+CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register
-CFG_SDRAM_BASE -- defines the DRAM Base
+CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================
flashoffset = 0x00000000
sramstart = 0x80000000
sramsize = 0x00008000
-mbar = 0xFC000000
-busfreq = 80 MHz
+mbar = 0xFC000000
+busfreq = 80 MHz
ethaddr = 00:E0:0C:BC:E5:60
ip_addr = 192.168.1.3
baudrate = 115200 bps
->
-> help
-? - alias for 'help'
-autoscr - run script from memory
-base - print or set address offset
-bdinfo - print Board Info structure
-boot - boot default, i.e., run 'bootcmd'
-bootd - boot default, i.e., run 'bootcmd'
+? - alias for 'help'
+base - print or set address offset
+bdinfo - print Board Info structure
+boot - boot default, i.e., run 'bootcmd'
+bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
-bootm - boot application image from memory
+bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
-bootvx - Boot vxWorks from an ELF image
-cmp - memory compare
+bootvx - Boot vxWorks from an ELF image
+cmp - memory compare
coninfo - print console devices and information
-cp - memory copy
-crc32 - checksum calculation
-date - get/set/reset date & time
-dcache - enable or disable data cache
-echo - echo args to console
-erase - erase FLASH memory
-flinfo - print FLASH memory information
-go - start application at address 'addr'
-help - print online help
-icache - enable or disable instruction cache
-icrc32 - checksum calculation
-iloop - infinite loop on address range
-imd - i2c memory display
-iminfo - print header information for application image
-imls - list all images found in flash
-imm - i2c memory modify (auto-incrementing)
-imw - memory write (fill)
-inm - memory modify (constant address)
-iprobe - probe to discover valid I2C chip addresses
+cp - memory copy
+crc32 - checksum calculation
+date - get/set/reset date & time
+dcache - enable or disable data cache
+echo - echo args to console
+erase - erase FLASH memory
+flinfo - print FLASH memory information
+go - start application at address 'addr'
+help - print online help
+i2c - I2C sub-system
+icache - enable or disable instruction cache
+iminfo - print header information for application image
+imls - list all images found in flash
itest - return true/false on integer compare
-loadb - load binary file over serial line (kermit mode)
-loads - load S-Record file over serial line
-loady - load binary file over serial line (ymodem mode)
-loop - infinite loop on address range
+loadb - load binary file over serial line (kermit mode)
+loads - load S-Record file over serial line
+loady - load binary file over serial line (ymodem mode)
+loop - infinite loop on address range
ls - list files in a directory (default /)
-md - memory display
-mii - MII utility commands
-mm - memory modify (auto-incrementing)
-mtest - simple RAM test
-mw - memory write (fill)
+md - memory display
+mii - MII utility commands
+mm - memory modify (auto-incrementing)
+mtest - simple RAM test
+mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nfs - boot image via network using NFS protocol
-nm - memory modify (constant address)
+nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
-reset - Perform RESET of the CPU
-run - run commands in an environment variable
+reset - Perform RESET of the CPU
+run - run commands in an environment variable
saveenv - save environment variables to persistent storage
-setenv - set environment variables
-sleep - delay execution for some time
+setenv - set environment variables
+sleep - delay execution for some time
+source - run script from memory
tftpboot- boot image via network using TFTP protocol
version - print monitor version
-> tftp 0x40800000 uImage
TFTP from server 192.168.1.3; our IP address is 192.168.1.3 Filename 'uImage'.
Load address: 0x40800000
Loading: #################################################################
- #################################################################
- ##########
+ #################################################################
+ ##########
done
Bytes transferred = 2053270 (1f5496 hex)
-> bootm 0x40800000
## Booting image at 40800000 ...
Image Name: Linux Kernel Image
- Created: 2007-11-07 20:33:08 UTC
+ Created: 2007-11-07 20:33:08 UTC
Image Type: M68K Linux Kernel Image (gzip compressed)
- Data Size: 2053206 Bytes = 2 MB
+ Data Size: 2053206 Bytes = 2 MB
Load Address: 40020000
Entry Point: 40020000
Verifying Checksum ... OK