doc: cleanup - move board READMEs into respective board directories

[u-boot] / doc / README.mpc8315erdb

diff --git a/doc/README.mpc8315erdb b/doc/README.mpc8315erdb
deleted file mode 100644 (file)
index b32132d..0000000
--- a/doc/README.mpc8315erdb
+++ /dev/null
@@ -1,105 +0,0 @@
-Freescale MPC8315ERDB Board
------------------------------------------
-
-1.     Board Switches and Jumpers
-
-       S3 is used to set CONFIG_SYS_RESET_SOURCE.
-
-       To boot the image at 0xFE000000 in NOR flash, use these DIP
-       switch settings for S3 S4:
-
-       +------+        +------+
-       |      |        | **** |
-       | **** |        |      |
-       +------+ ON     +------+ ON
-         4321            4321
-       (where the '*' indicates the position of the tab of the switch.)
-
-       To boot the image at the beginning of NAND flash, use these
-       DIP switch settings for S3 S4:
-
-       +------+        +------+
-       | *    |        |  *** |
-       |  *** |        | *    |
-       +------+ ON     +------+ ON
-         4321            4321
-       (where the '*' indicates the position of the tab of the switch.)
-
-       When booting from NAND, use u-boot-nand.bin, not u-boot.bin.
-
-2.     Memory Map
-       The memory map looks like this:
-
-       0x0000_0000     0x07ff_ffff     DDR              128M
-       0x8000_0000     0x8fff_ffff     PCI MEM          256M
-       0x9000_0000     0x9fff_ffff     PCI_MMIO         256M
-       0xe000_0000     0xe00f_ffff     IMMR             1M
-       0xe030_0000     0xe03f_ffff     PCI IO           1M
-       0xe060_0000     0xe060_7fff     NAND FLASH (CS1) 32K
-       0xfe00_0000     0xfe7f_ffff     NOR FLASH (CS0)  8M
-
-       When booting from NAND, NAND flash is CS0 and NOR flash
-       is CS1.
-
-3.     Definitions
-
-3.1    Explanation of NEW definitions in:
-
-       include/configs/MPC8315ERDB.h
-
-       CONFIG_MPC83xx          MPC83xx family
-       CONFIG_MPC831x          MPC831x specific
-       CONFIG_MPC8315          MPC8315 specific
-       CONFIG_MPC8315ERDB      MPC8315ERDB board specific
-
-4.     Compilation
-
-       Assuming you're using BASH (or similar) as your shell:
-
-       export CROSS_COMPILE=your-cross-compiler-prefix-
-       make distclean
-       make MPC8315ERDB_config (or MPC8315ERDB_NAND_config for u-boot-nand.bin)
-       make all
-
-5.     Downloading and Flashing Images
-
-5.1    Reflash U-boot Image using U-boot
-
-       NOR flash:
-
-       tftp 40000 u-boot.bin
-       protect off all
-       erase fe000000 fe1fffff
-
-       cp.b 40000 fe000000 xxxx
-       protect on all
-
-       You have to supply the correct byte count with 'xxxx'
-       from the TFTP result log.
-
-       NAND flash:
-
-       =>tftpboot $loadaddr <filename>
-       =>nand erase 0 0x80000
-       =>nand write $loadaddr 0 0x80000
-
-       ...where 0x80000 is the filesize rounded up to
-       the next 0x20000 increment.
-
-5.2    Downloading and Booting Linux Kernel
-
-       Ensure that all networking-related environment variables are set
-       properly (including ipaddr, serverip, gatewayip (if needed),
-       netmask, ethaddr, eth1addr, rootpath (if using NFS root),
-       fdtfile, and bootfile).
-
-       Then, do one of the following, depending on whether you
-       want an NFS root or a ramdisk root:
-
-       =>run nfsboot
-       or
-       =>run ramboot
-
-6      Notes
-
-       The console baudrate for MPC8315ERDB is 115200bps.