address of u-boot MTD partition in NAND.
CONFIG_CMD_NAND
- Enables NAND support and commmands.
+ Enables NAND support and commands.
CONFIG_CMD_NAND_TORTURE
Enables the torture command (see description of this command below).
Example of new init to be added to the end of an existing driver
init:
- /*
- * devnum is the device number to be used in nand commands
- * and in mtd->name. Must be less than
- * CONFIG_SYS_NAND_MAX_DEVICE.
- */
- mtd = &nand_info[devnum];
-
/* chip is struct nand_chip, and is now provided by the driver. */
- mtd->priv = &chip;
+ mtd = nand_to_mtd(&chip);
/*
* Fill in appropriate values if this driver uses these fields,
if (nand_scan_tail(mtd))
error out
- if (nand_register(devnum))
+ /*
+ * devnum is the device number to be used in nand commands
+ * and in mtd->name. Must be less than CONFIG_SYS_MAX_NAND_DEVICE.
+ */
+ if (nand_register(devnum, mtd))
error out
In addition to providing more flexibility to the driver, it reduces
And fetching device parameters flashed on device, by parsing
ONFI parameter page.
- CONFIG_BCH
- Enables software based BCH ECC algorithm present in lib/bch.c
- This is used by SoC platforms which do not have built-in ELM
- hardware engine required for BCH ECC correction.
-
- CONFIG_SYS_NAND_BUSWIDTH_16BIT
- Indicates that NAND device has 16-bit wide data-bus. In absence of this
- config, bus-width of NAND device is assumed to be either 8-bit and later
- determined by reading ONFI params.
- Above config is useful when NAND device's bus-width information cannot
- be determined from on-chip ONFI params, like in following scenarios:
- - SPL boot does not support reading of ONFI parameters. This is done to
- keep SPL code foot-print small.
- - In current U-Boot flow using nand_init(), driver initialization
- happens in board_nand_init() which is called before any device probe
- (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
- not available while configuring controller. So a static CONFIG_NAND_xx
- is needed to know the device's bus-width in advance.
- Some drivers using above config are:
- drivers/mtd/nand/mxc_nand.c
- drivers/mtd/nand/ndfc.c
- drivers/mtd/nand/omap_gpmc.c
-
-
Platform specific options
=========================
CONFIG_NAND_OMAP_GPMC
However, for 4K pagesize NAND
NAND_PAGESIZE = 4096
- NAND_OOBSIZE = 64
+ NAND_OOBSIZE = 224
ECC_BYTES = 26
2 + (4096 / 512) * 26 = 210 < NAND_OOBSIZE
Thus BCH16 can be supported on 4K page NAND.
DANGEROUS!!! Factory set bad blocks will be lost. Use only
to remove artificial bad blocks created with the "markbad" command.
- "torture offset"
+ "torture offset [size]"
Torture block to determine if it is still reliable.
Enabled by the CONFIG_CMD_NAND_TORTURE configuration option.
This command returns 0 if the block is still reliable, else 1.
automate actions following a nand->write() error. This would e.g. be required
in order to program or update safely firmware to NAND, especially for the UBI
part of such firmware.
+ Optionally, a second parameter size can be given to test multiple blocks with
+ one call. If size is not a multiple of the NAND's erase size, then the block
+ that contains offset + size will be tested in full. If used with size, this
+ command returns 0 if all tested blocks have been found reliable, else 1.
NAND locking command (for chips with active LOCKPRE pin)