The flash type is intel 28F640Jx (4096x16) [one device]. Base address
is 0xFF80_0000 which is also where the Hardware Reset Configuration
-Word (HRCW) is stored. Caution should be used to not overwrite the
-HRCW, or "CF RCW" with a Wind River ICE will be required to restore
-the HRCW and allow the board to enter background mode for further
-steps in the flash process.
+Word (HRCW) is stored. Caution should be used to not reset the
+board without having a valid HRCW in place (i.e. erased flash) as
+then a Wind River ICE will be required to restore the HRCW and flash
+image.
Restoring a corrupted or missing flash image:
=============================================
+Note that U-boot versions up to and including 2009.06 had essentially
+two copies of u-boot in flash; one at the very beginning, which set
+the HRCW, and one at the very end, which was the image that was run.
+As of this point in time, the two have been combined into just one
+at the beginning of flash, which provides both the HRCW, and the image
+that is executed. This frees up the remainder of flash for other uses.
+Use of the u-boot command "fli" will indicate what parts are in use.
Details for storing U-boot to flash using a Wind River ICE can be found
on page 19 of the board manual (request ERG-00328-001). The following
is a summary of that information:
- Select the appropriate flash type (listed above)
- Prepare a u-boot image by using the Wind River Convert utility;
by using "Convert and Add file" on the ELF file from your build.
- Convert from FFF0_0000 to FFFF_FFFF (or to FFF3_FFFF if you are
- trying to preserve your old environment settings).
- - Set the start address of the erase/flash process to FFF0_0000
+ Convert from FF80_0000 to FFFF_FFFF (or to FF83_FFFF if you are
+ trying to preserve your old environment settings and user flash).
+ - Set the start address of the erase/flash process to FF80_0000
- Set the target RAM required to 64kB.
- Select sectors for erasing (see note on enviroment below)
- Select Erase and Reprogram.
use all the remaining register file content.
If you wish to preserve your prior U-Boot environment settings,
-then convert (and erase to) 0xFFF3FFFF instead of 0xFFFFFFFF.
+then convert (and erase to) 0xFF83FFFF instead of 0xFFFFFFFF.
The size for converting (and erasing) must be at least as large
as u-boot.bin.
tftp 200000 u-boot.bin
protect off all
- erase fff00000 fff3ffff
- cp.b 200000 fff00000 3ffff
+ erase ff800000 ff83ffff
+ cp.b 200000 ff800000 40000
protect on all
+You may wish to do a "md ff800000 20" operation as a prefix and postfix
+to the above steps to inspect/compare the HRCW before/after as an extra
+safety check before resetting the board upon completion of the reflash.
PCI:
====
-This board and U-Boot have been tested with PCI built in, on a SBC8349
-and confirmed that the "pci" command showed the intel e1000 that was
-present in the PCI slot. Note that if a 33MHz 32bit card is inserted
-in the slot, then the whole board will clock down to a 33MHz base
-clock instead of the default 66MHz. This will change the baud clocks
-and mess up your serial console output. If you want to use a 33MHz PCI
-card, then you should build a U-Boot with #undef PCI_66M in the
-include/configs/sbc8349.h and store this to flash prior to powering down
-the board and inserting the 33MHz PCI card.
-
-By default PCI support is disabled to better support very early
-revision MPC834x chips with possible PCI issues. Also PCI support is
-untested on the sbc8347 variants at this point in time.
-
-
- Paul Gortmaker, 01/2007
+There are three configuration choices:
+ sbc8349_config
+ sbc8349_PCI_33_config
+ sbc8349_PCI_66_config
+
+The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
+will be left empty (M66EN high), and so the board will operate with
+a base clock of 66MHz. Note that you need both PCI enabled in u-boot
+and linux in order to have functional PCI under linux. The only
+reason for choosing to not enable PCI would be if you had a very
+early (rev 1.0) CPU with possible PCI issues.
+
+The second enables PCI support and builds for a 33MHz clock rate. Note
+that if a 33MHz 32bit card is inserted in the slot, then the whole board
+will clock down to a 33MHz base clock instead of the default 66MHz. This
+will change the baud clocks and mess up your serial console output if you
+were previously running at 66MHz. If you want to use a 33MHz PCI card,
+then you should build a U-Boot with sbc8349_PCI_33_config and store this
+to flash prior to powering down the board and inserting the 33MHz PCI
+card.
+
+The third option builds PCI support in, and leaves the clocking at the
+default 66MHz. This has been tested with an intel PCI-X e1000 card.
+This is also the appropriate choice for people with a recent (non 1.0)
+CPU who currently have the PCI slot physically empty, but intend to
+possibly add a PCI-X card at a later date.
+
+ => pci
+ Scanning PCI devices on bus 0
+ BusDevFun VendorId DeviceId Device Class Sub-Class
+ _____________________________________________________________
+ 00.00.00 0x1957 0x0080 Processor 0x20
+ 00.11.00 0x8086 0x1026 Network controller 0x00
+ =>