doc: cleanup - move board READMEs into respective board directories

[u-boot] / doc / README.sh7785lcr

diff --git a/doc/README.sh7785lcr b/doc/README.sh7785lcr
deleted file mode 100644 (file)
index 56455fc..0000000
--- a/doc/README.sh7785lcr
+++ /dev/null
@@ -1,123 +0,0 @@
-========================================
-Renesas Technology R0P7785LC0011RL board
-========================================
-
-This board specification:
-=========================
-
-The R0P7785LC0011RL(board config name:sh7785lcr) has the following device:
-
- - SH7785 (SH-4A)
- - DDR2-SDRAM 512MB
- - NOR Flash 64MB
- - 2D Graphic controller
- - SATA controller
- - Ethernet controller
- - USB host/peripheral controller
- - SD controller
- - I2C controller
- - RTC
-
-This board has 2 physical memory maps. It can be changed with DIP switch(S2-5).
-
- phys address                  | S2-5 = OFF    | S2-5 = ON
- -------------------------------+---------------+---------------
- 0x00000000 - 0x03ffffff(CS0)  | NOR Flash     | NOR Flash
- 0x04000000 - 0x05ffffff(CS1)  | PLD           | PLD
- 0x06000000 - 0x07ffffff(CS1)  | reserved      | I2C
- 0x08000000 - 0x0bffffff(CS2)  | USB           | DDR SDRAM
- 0x0c000000 - 0x0fffffff(CS3)  | SD            | DDR SDRAM
- 0x10000000 - 0x13ffffff(CS4)  | SM107         | SM107
- 0x14000000 - 0x17ffffff(CS5)  | I2C           | USB
- 0x18000000 - 0x1bffffff(CS6)  | reserved      | SD
- 0x40000000 - 0x5fffffff       | DDR SDRAM     | (cannot use)
-
-
-configuration for This board:
-=============================
-
-You can choose configuration as follows:
-
- - make sh7785lcr_config
- - make sh7785lcr_32bit_config
-
-When you use "make sh7785lcr_config", there is build U-Boot for 29-bit
-address mode. This mode can use 128MB DDR-SDRAM.
-
-When you use "make sh7785lcr_32bit_config", there is build U-Boot for 32-bit
-extended address mode. This mode can use 384MB DDR-SDRAM. And if you run
-"pmb" command, this mode can use 512MB DDR-SDRAM.
-
- * 32-bit extended address mode PMB mapping *
-  a) on start-up
-   virt                | phys          | size          | device
-   -------------+---------------+---------------+---------------
-   0x88000000  | 0x48000000    | 384MB         | DDR-SDRAM (Cacheable)
-   0xa0000000  | 0x00000000    | 64MB          | NOR Flash
-   0xa4000000  | 0x04000000    | 16MB          | PLD
-   0xa6000000  | 0x08000000    | 16MB          | USB
-   0xa8000000  | 0x48000000    | 384MB         | DDR-SDRAM (Non-cacheable)
-
-  b) after "pmb" command
-   virt                | phys          | size          | device
-   -------------+---------------+---------------+---------------
-   0x80000000  | 0x40000000    | 512MB         | DDR-SDRAM (Cacheable)
-   0xa0000000  | 0x40000000    | 512MB         | DDR-SDRAM (Non-cacheable)
-
-
-This board specific command:
-============================
-
-This board has the following its specific command:
-
- - hwtest
- - printmac
- - setmac
- - pmb (sh7785lcr_32bit_config only)
-
-
-1. hwtest
-
-This is self-check command. This command has the following options:
-
- - all         : test all hardware
- - pld         : output PLD version
- - led         : turn on LEDs
- - dipsw       : test DIP switch
- - sm107       : output SM107 version
- - net         : check RTL8110 ID
- - sata                : check SiI3512 ID
- - net         : output PCI slot device ID
-
-i.e)
-=> hwtest led
-turn on LEDs 3, 5, 7, 9
-turn on LEDs 4, 6, 8, 10
-
-=> hwtest net
-Ethernet OK
-
-
-2. printmac
-
-This command outputs MAC address of this board.
-
-i.e)
-=> printmac
-MAC = 00:00:87:**:**:**
-
-
-3. setmac
-
-This command writes MAC address of this board.
-
-i.e)
-=> setmac 00:00:87:**:**:**
-
-
-4. pmb
-
-This command change PMB for DDR-SDRAM all mapping. However you cannot use
-NOR Flash and USB Host on U-Boot when you run this command.
-i.e)
-=> pmb