doc: dt-bindings: Describe Freescale TSEC ethernet controller

[u-boot] / doc / README.uniphier

diff --git a/doc/README.uniphier b/doc/README.uniphier
index e936f4025432a7f2f57d70936809d08c3b803f5a..bce70cf5fe433ecb64e77b21f4973658a695f788 100644 (file)
--- a/doc/README.uniphier
+++ b/doc/README.uniphier
@@ -28,22 +28,38 @@ Tested toolchains
 Compile the source
 ------------------
 
-PH1-sLD3:
-    $ make ph1_sld3_defconfig
+PH1-sLD3 reference board:
+    $ make uniphier_sld3_defconfig
     $ make CROSS_COMPILE=arm-linux-gnueabi-
 
-PH1-LD4:
-    $ make ph1_ld4_defconfig
+PH1-LD4 reference board:
+    $ make uniphier_ld4_sld8_defconfig
     $ make CROSS_COMPILE=arm-linux-gnueabi-
 
-PH1-Pro4:
-    $ make ph1_pro4_defconfig
+PH1-sLD8 reference board:
+    $ make uniphier_ld4_sld8_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-sld8-ref
+
+PH1-Pro4 reference board:
+    $ make uniphier_pro4_defconfig
     $ make CROSS_COMPILE=arm-linux-gnueabi-
 
-PH1-sLD8:
-    $ make ph1_sld8_defconfig
+PH1-Pro5 4KBOX Board:
+    $ make uniphier_pro5_defconfig
     $ make CROSS_COMPILE=arm-linux-gnueabi-
 
+ProXstream2 Gentil board:
+    $ make uniphier_pxs2_ld6b_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-proxstream2-gentil
+
+ProXstream2 Vodka board:
+    $ make uniphier_pxs2_ld6b_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi-
+
+PH1-LD6b reference board:
+    $ make uniphier_pxs2_ld6b_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld6b-ref
+
 You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-"
 to use your favorite compiler.
 
@@ -103,7 +119,7 @@ The recommended bit switch settings are as follows:
 
  SW8    OFF(1)/ON(0)   Description
  ------------------------------------------
- bit 1    ---->        CS1_SPLIT
+ bit 1    <----        CS1_SPLIT
  bit 2    <----        CASE9_ON
  bit 3    <----        CASE10_ON
  bit 4  Don't Care     Reserve
@@ -117,10 +133,10 @@ as follows:
 
  BKSZ    Description              RAM slot            Peripherals
  --------------------------------------------------------------------
- 0b00   15MB RAM / 1MB Peri    00000000-0effffff    0f000000-0fffffff
- 0b01   31MB RAM / 1MB Peri    00000000-1effffff    1f000000-1fffffff
- 0b10   64MB RAM / 1MB Peri    00000000-3effffff    3f000000-3fffffff
- 0b11  127MB RAM / 1MB Peri    00000000-7effffff    7f000000-7fffffff
+ 0b00   15MB RAM / 1MB Peri    00000000-00efffff    00f00000-00ffffff
+ 0b01   31MB RAM / 1MB Peri    00000000-01efffff    01f00000-01ffffff
+ 0b10   64MB RAM / 1MB Peri    00000000-03efffff    03f00000-03ffffff
+ 0b11  127MB RAM / 1MB Peri    00000000-07efffff    07f00000-07ffffff
 
 Set BSKZ[1:0] to 0b01 for U-Boot.
 This mode is the most handy because EA[24] is always supported by the save pin