doc: fix use of deprecated config file in the example

[openocd] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index def0c9d6c5f31b84119c9800d3f58ea198280364..1c005f2f856368cf42836b5c4e8360561415ec18 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -2114,6 +2114,7 @@ In such cases, just specify the relevant port number as "disabled".
 If you disable all access through TCP/IP, you will need to
 use the command line @option{-pipe} option.
 
+@anchor{gdb_port}
 @deffn {Command} gdb_port [number]
 @cindex GDB server
 Normally gdb listens to a TCP/IP port, but GDB can also
@@ -2139,11 +2140,15 @@ The GDB port for the first target will be the base port, the
 second target will listen on gdb_port + 1, and so on.
 When not specified during the configuration stage,
 the port @var{number} defaults to 3333.
+When @var{number} is not a numeric value, incrementing it to compute
+the next port number does not work. In this case, specify the proper
+@var{number} for each target by using the option @code{-gdb-port} of the
+commands @command{target create} or @command{$target_name configure}.
+@xref{gdbportoverride,,option -gdb-port}.
 
 Note: when using "gdb_port pipe", increasing the default remote timeout in
 gdb (with 'set remotetimeout') is recommended. An insufficient timeout may
 cause initialization to fail with "Unknown remote qXfer reply: OK".
-
 @end deffn
 
 @deffn {Command} tcl_port [number]
@@ -4441,7 +4446,7 @@ The value should normally correspond to a static mapping for the
 @item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
 @var{rtos_type} can be one of @option{auto}, @option{eCos},
 @option{ThreadX}, @option{FreeRTOS}, @option{linux}, @option{ChibiOS},
-@option{embKernel}, @option{mqx}, @option{uCOS-III}
+@option{embKernel}, @option{mqx}, @option{uCOS-III}, @option{nuttx}
 @xref{gdbrtossupport,,RTOS Support}.
 
 @item @code{-defer-examine} -- skip target examination at initial JTAG chain
@@ -4458,6 +4463,13 @@ to the target. Currently, only the @code{aarch64} target makes use of this optio
 where it is a mandatory configuration for the target run control.
 @xref{armcrosstrigger,,ARM Cross-Trigger Interface},
 for instruction on how to declare and control a CTI instance.
+
+@anchor{gdbportoverride}
+@item @code{-gdb-port} @var{number} -- see command @command{gdb_port} for the
+possible values of the parameter @var{number}, which are not only numeric values.
+Use this option to override, for this target only, the global parameter set with
+command @command{gdb_port}.
+@xref{gdb_port,,command gdb_port}.
 @end itemize
 @end deffn
 
@@ -8777,7 +8789,7 @@ baud with our custom divisor to get 12MHz)
 @item @code{itmdump -f /dev/ttyUSB1 -d1}
 @item OpenOCD invocation line:
 @example
-openocd -f interface/stlink-v2-1.cfg \
+openocd -f interface/stlink.cfg \
         -c "transport select hla_swd" \
         -f target/stm32l1.cfg \
         -c "tpiu config external uart off 24000000 12000000"
@@ -8800,8 +8812,8 @@ Enable or disable trace output for all ITM stimulus ports.
 @deffn Command {cortex_m maskisr} (@option{auto}|@option{on}|@option{off})
 Control masking (disabling) interrupts during target step/resume.
 
-The @option{auto} option handles interrupts during stepping a way they get
-served but don't disturb the program flow. The step command first allows
+The @option{auto} option handles interrupts during stepping in a way that they
+get served but don't disturb the program flow. The step command first allows
 pending interrupt handlers to execute, then disables interrupts and steps over
 the next instruction where the core was halted. After the step interrupts
 are enabled again. If the interrupt handlers don't complete within 500ms,
@@ -9806,6 +9818,7 @@ Currently supported rtos's include:
 @item @option{embKernel}
 @item @option{mqx}
 @item @option{uCOS-III}
+@item @option{nuttx}
 @end itemize
 
 @quotation Note
@@ -9841,6 +9854,8 @@ Rtos::sListSuspended, Rtos::sMaxPriorities, Rtos::sCurrentTaskCount.
 _mqx_kernel_data, MQX_init_struct.
 @item uC/OS-III symbols
 OSRunning, OSTCBCurPtr, OSTaskDbgListPtr, OSTaskQty
+@item nuttx symbols
+g_readytorun, g_tasklisttable
 @end table
 
 For most RTOS supported the above symbols will be exported by default. However for