a board with an Atmel AT91SAM7X256 microcontroller:
@example
-source [find interface/signalyzer.cfg]
+source [find interface/ftdi/signalyzer.cfg]
# GDB can also flash my flash!
gdb_memory_map enable
Here is the command line equivalent of that configuration:
@example
-openocd -f interface/signalyzer.cfg \
+openocd -f interface/ftdi/signalyzer.cfg \
-c "gdb_memory_map enable" \
-c "gdb_flash_program enable" \
-f target/sam7x256.cfg
Cirrus Logic EP93xx based single-board computer bit-banging (in development)
@end deffn
-@deffn {Interface Driver} {ft2232}
-FTDI FT2232 (USB) based devices over one of the userspace libraries.
-
-Note that this driver has several flaws and the @command{ftdi} driver is
-recommended as its replacement.
-
-These interfaces have several commands, used to configure the driver
-before initializing the JTAG scan chain:
-
-@deffn {Config Command} {ft2232_device_desc} description
-Provides the USB device description (the @emph{iProduct string})
-of the FTDI FT2232 device. If not
-specified, the FTDI default value is used. This setting is only valid
-if compiled with FTD2XX support.
-@end deffn
-
-@deffn {Config Command} {ft2232_serial} serial-number
-Specifies the @var{serial-number} of the FTDI FT2232 device to use,
-in case the vendor provides unique IDs and more than one FT2232 device
-is connected to the host.
-If not specified, serial numbers are not considered.
-(Note that USB serial numbers can be arbitrary Unicode strings,
-and are not restricted to containing only decimal digits.)
-@end deffn
-
-@deffn {Config Command} {ft2232_layout} name
-Each vendor's FT2232 device can use different GPIO signals
-to control output-enables, reset signals, and LEDs.
-Currently valid layout @var{name} values include:
-@itemize @minus
-@item @b{axm0432_jtag} Axiom AXM-0432
-@item @b{comstick} Hitex STR9 comstick
-@item @b{cortino} Hitex Cortino JTAG interface
-@item @b{evb_lm3s811} TI/Luminary Micro EVB_LM3S811 as a JTAG interface,
-either for the local Cortex-M3 (SRST only)
-or in a passthrough mode (neither SRST nor TRST)
-This layout can not support the SWO trace mechanism, and should be
-used only for older boards (before rev C).
-@item @b{luminary_icdi} This layout should be used with most TI/Luminary
-eval boards, including Rev C LM3S811 eval boards and the eponymous
-ICDI boards, to debug either the local Cortex-M3 or in passthrough mode
-to debug some other target. It can support the SWO trace mechanism.
-@item @b{flyswatter} Tin Can Tools Flyswatter
-@item @b{icebear} ICEbear JTAG adapter from Section 5
-@item @b{jtagkey} Amontec JTAGkey and JTAGkey-Tiny (and compatibles)
-@item @b{jtagkey2} Amontec JTAGkey2 (and compatibles)
-@item @b{m5960} American Microsystems M5960
-@item @b{olimex-jtag} Olimex ARM-USB-OCD and ARM-USB-Tiny
-@item @b{oocdlink} OOCDLink
-@c oocdlink ~= jtagkey_prototype_v1
-@item @b{redbee-econotag} Integrated with a Redbee development board.
-@item @b{redbee-usb} Integrated with a Redbee USB-stick development board.
-@item @b{sheevaplug} Marvell Sheevaplug development kit
-@item @b{signalyzer} Xverve Signalyzer
-@item @b{stm32stick} Hitex STM32 Performance Stick
-@item @b{turtelizer2} egnite Software turtelizer2
-@item @b{usbjtag} "USBJTAG-1" layout described in the OpenOCD diploma thesis
-@end itemize
-@end deffn
-
-@deffn {Config Command} {ft2232_vid_pid} [vid pid]+
-The vendor ID and product ID of the FTDI FT2232 device. If not specified, the FTDI
-default values are used.
-Currently, up to eight [@var{vid}, @var{pid}] pairs may be given, e.g.
-@example
-ft2232_vid_pid 0x0403 0xcff8 0x15ba 0x0003
-@end example
-@end deffn
-
-@deffn {Config Command} {ft2232_latency} ms
-On some systems using FT2232 based JTAG interfaces the FT_Read function call in
-ft2232_read() fails to return the expected number of bytes. This can be caused by
-USB communication delays and has proved hard to reproduce and debug. Setting the
-FT2232 latency timer to a larger value increases delays for short USB packets but it
-also reduces the risk of timeouts before receiving the expected number of bytes.
-The OpenOCD default value is 2 and for some systems a value of 10 has proved useful.
-@end deffn
-
-@deffn {Config Command} {ft2232_channel} channel
-Used to select the channel of the ft2232 chip to use (between 1 and 4).
-The default value is 1.
-@end deffn
-
-For example, the interface config file for a
-Turtelizer JTAG Adapter looks something like this:
-
-@example
-interface ft2232
-ft2232_device_desc "Turtelizer JTAG/RS232 Adapter"
-ft2232_layout turtelizer2
-ft2232_vid_pid 0x0403 0xbdc8
-@end example
-@end deffn
-
@deffn {Interface Driver} {ftdi}
This driver is for adapters using the MPSSE (Multi-Protocol Synchronous Serial
Engine) mode built into many FTDI chips, such as the FT2232, FT4232 and FT232H.
-It is a complete rewrite to address a large number of problems with the ft2232
-interface driver.
The driver is using libusb-1.0 in asynchronous mode to talk to the FTDI device,
-bypassing intermediate libraries like libftdi of D2XX. Performance-wise it is
-consistently faster than the ft2232 driver, sometimes several times faster.
+bypassing intermediate libraries like libftdi of D2XX.
A major improvement of this driver is that support for new FTDI based adapters
can be added competely through configuration files, without the need to patch
@end example
@end deffn
-@deffn {Command} {usb_blaster_lowlevel_driver} (@option{ftdi}|@option{ftd2xx}|@option{ublast2})
+@deffn {Command} {usb_blaster_lowlevel_driver} (@option{ftdi}|@option{ublast2})
Chooses the low level access method for the adapter. If not specified,
@option{ftdi} is selected unless it wasn't enabled during the
configure stage. USB-Blaster II needs @option{ublast2}.
@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
@var{rtos_type} can be one of @option{auto}|@option{eCos}|@option{ThreadX}|
-@option{FreeRTOS}|@option{linux}|@option{ChibiOS}|@option{embKernel}|@option{mqx}
+@option{FreeRTOS}|@option{linux}|@option{ChibiOS}|@option{embKernel}|@option{mqx}|
+@option{uCOS-III}
@xref{gdbrtossupport,,RTOS Support}.
+@item @code{-defer-examine} -- skip target examination at initial JTAG chain
+scan and after a reset. A manual call to arp_examine is required to
+access the target for debugging.
+
@end itemize
@end deffn
The commands supported by OpenOCD target objects are:
-@deffn Command {$target_name arp_examine}
+@deffn Command {$target_name arp_examine} @option{allow-defer}
@deffnx Command {$target_name arp_halt}
@deffnx Command {$target_name arp_poll}
@deffnx Command {$target_name arp_reset}
This will first attempt a comparison using a CRC checksum, if this fails it will try a binary compare.
@end deffn
+@deffn Command {verify_image_checksum} filename address [@option{bin}|@option{ihex}|@option{elf}]
+Verify @var{filename} against target memory starting at @var{address}.
+The file format may optionally be specified
+(@option{bin}, @option{ihex}, or @option{elf})
+This perform a comparison using a CRC checksum only
+@end deffn
+
@section Breakpoint and Watchpoint commands
@cindex breakpoint
Supervisor Call vector by OpenOCD.
@end deffn
+@deffn Command {arm semihosting_fileio} [@option{enable}|@option{disable}]
+@cindex ARM semihosting
+Display status of semihosting fileio, after optionally changing that
+status.
+
+Enabling this option forwards semihosting I/O to GDB process using the
+File-I/O remote protocol extension. This is especially useful for
+interacting with remote files or displaying console messages in the
+debugger.
+@end deffn
+
@section ARMv4 and ARMv5 Architecture
@cindex ARMv4
@cindex ARMv5
@item @option{ChibiOS}
@item @option{embKernel}
@item @option{mqx}
+@item @option{uCOS-III}
@end itemize
@quotation Note
Rtos::sListSuspended, Rtos::sMaxPriorities, Rtos::sCurrentTaskCount.
@item mqx symbols
_mqx_kernel_data, MQX_init_struct.
+@item uC/OS-III symbols
+OSRunning, OSTCBCurPtr, OSTaskDbgListPtr, OSTaskQty
@end table
For most RTOS supported the above symbols will be exported by default. However for
-some, eg. FreeRTOS, extra steps must be taken.
+some, eg. FreeRTOS and uC/OS-III, extra steps must be taken.
These RTOSes may require additional OpenOCD-specific file to be linked
along with the project:
@table @code
@item FreeRTOS
contrib/rtos-helpers/FreeRTOS-openocd.c
+@item uC/OS-III
+contrib/rtos-helpers/uCOS-III-openocd.c
@end table
@node Tcl Scripting API
@b{Laptops running on battery have this problem too...}
-@item @b{USB Power} When using the Amontec JTAGkey, sometimes OpenOCD crashes with the
-following error messages: "Error: ft2232.c:201 ft2232_read(): FT_Read returned:
-4" and "Error: ft2232.c:365 ft2232_send_and_recv(): couldn't read from FT2232".
-What does that mean and what might be the reason for this?
-
-First of all, the reason might be the USB power supply. Try using a self-powered
-hub instead of a direct connection to your computer. Secondly, the error code 4
-corresponds to an FT_IO_ERROR, which means that the driver for the FTDI USB
-chip ran into some sort of error - this points us to a USB problem.
-
@item @b{GDB Disconnects} When using the Amontec JTAGkey, sometimes OpenOCD crashes with the following
error message: "Error: gdb_server.c:101 gdb_get_char(): read: 10054".
What does that mean and what might be the reason for this?
projects / openocd / blobdiff