@item any search dir specified on the command line using the @option{-s} option,
@item any search dir specified using the @command{add_script_search_dir} command,
@item @file{$HOME/.openocd} (not on Windows),
+@item a directory in the @env{OPENOCD_SCRIPTS} environment variable (if set),
@item the site wide script library @file{$pkgdatadir/site} and
@item the OpenOCD-supplied script library @file{$pkgdatadir/scripts}.
@end enumerate
second target will listen on gdb_port + 1, and so on.
When not specified during the configuration stage,
the port @var{number} defaults to 3333.
+
+Note: when using "gdb_port pipe", increasing the default remote timeout in
+gdb (with 'set remotetimeout') is recommended. An insufficient timeout may
+cause initialization to fail with "Unknown remote qXfer reply: OK".
+
@end deffn
@deffn {Command} tcl_port [number]
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {flash read_bank} num filename offset length
+Read @var{length} bytes from the flash bank @var{num} starting at @var{offset}
+and write the contents to the binary @file{filename}.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {flash verify_bank} num filename offset
+Compare the contents of the binary file @var{filename} with the contents of the
+flash @var{num} starting at @var{offset}. Fails if the contents do not match.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {flash write_image} [erase] [unlock] filename [offset] [type]
Write the image @file{filename} to the current target's flash bank(s).
Only loadable sections from the image are written.
@c "cfi part_id" disabled
@end deffn
+@deffn {Flash Driver} jtagspi
+@cindex Generic JTAG2SPI driver
+@cindex SPI
+@cindex jtagspi
+@cindex bscan_spi
+Several FPGAs and CPLDs can retrieve their configuration (bitstream) from a
+SPI flash connected to them. To access this flash from the host, the device
+is first programmed with a special proxy bitstream that
+exposes the SPI flash on the device's JTAG interface. The flash can then be
+accessed through JTAG.
+
+Since signaling between JTAG and SPI is compatible, all that is required for
+a proxy bitstream is to connect TDI-MOSI, TDO-MISO, TCK-CLK and activate
+the flash chip select when the JTAG state machine is in SHIFT-DR. Such
+a bitstream for several Xilinx FPGAs can be found in
+@file{contrib/loaders/flash/fpga/xilinx_bscan_spi.py}. It requires migen
+(@url{http://github.com/m-labs/migen}) and a Xilinx toolchain to build.
+
+This flash bank driver requires a target on a JTAG tap and will access that
+tap directly. Since no support from the target is needed, the target can be a
+"testee" dummy. Since the target does not expose the flash memory
+mapping, target commands that would otherwise be expected to access the flash
+will not work. These include all @command{*_image} and
+@command{$target_name m*} commands as well as @command{program}. Equivalent
+functionality is available through the @command{flash write_bank},
+@command{flash read_bank}, and @command{flash verify_bank} commands.
+
+@itemize
+@item @var{ir} ... is loaded into the JTAG IR to map the flash as the JTAG DR.
+For the bitstreams generated from @file{xilinx_bscan_spi.py} this is the
+@var{USER1} instruction.
+@item @var{dr_length} ... is the length of the DR register. This will be 1 for
+@file{xilinx_bscan_spi.py} bitstreams and most other cases.
+@end itemize
+
+@example
+target create $_TARGETNAME testee -chain-position $_CHIPNAME.fpga
+set _XILINX_USER1 0x02
+set _DR_LENGTH 1
+flash bank $_FLASHNAME spi 0x0 0 0 0 $_TARGETNAME $_XILINX_USER1 $_DR_LENGTH
+@end example
+@end deffn
+
@deffn {Flash Driver} lpcspifi
@cindex NXP SPI Flash Interface
@cindex SPIFI
@end deffn
@end deffn
+@deffn {Flash Driver} atsamv
+@cindex atsamv
+All members of the ATSAMV, ATSAMS, and ATSAME families from
+Atmel include internal flash and use ARM's Cortex-M7 core.
+This driver uses the same cmd names/syntax as @xref{at91sam3}.
+@end deffn
+
@deffn {Flash Driver} at91sam7
All members of the AT91SAM7 microcontroller family from Atmel include
internal flash and use ARM7TDMI cores. The driver automatically
supported.}
@end deffn
+@deffn {Flash Driver} fm3
+All members of the FM3 microcontroller family from Fujitsu
+include internal flash and use ARM Cortex M3 cores.
+The @var{fm3} driver uses the @var{target} parameter to select the
+correct bank config, it can currently be one of the following:
+@code{mb9bfxx1.cpu}, @code{mb9bfxx2.cpu}, @code{mb9bfxx3.cpu},
+@code{mb9bfxx4.cpu}, @code{mb9bfxx5.cpu} or @code{mb9bfxx6.cpu}.
+
+@example
+flash bank $_FLASHNAME fm3 0 0 0 0 $_TARGETNAME
+@end example
+@end deffn
+
@deffn {Flash Driver} lpc2000
This is the driver to support internal flash of all members of the
LPC11(x)00 and LPC1300 microcontroller families and most members of
@end deffn
@end deffn
+@deffn {Flash Driver} mdr
+This drivers handles the integrated NOR flash on Milandr Cortex-M
+based controllers. A known limitation is that the Info memory can't be
+read or verified as it's not memory mapped.
+
+@example
+flash bank <name> mdr <base> <size> \
+ 0 0 <target#> @var{type} @var{page_count} @var{sec_count}
+@end example
+
+@itemize @bullet
+@item @var{type} - 0 for main memory, 1 for info memory
+@item @var{page_count} - total number of pages
+@item @var{sec_count} - number of sector per page count
+@end itemize
+
+Example usage:
+@example
+if @{ [info exists IMEMORY] && [string equal $IMEMORY true] @} @{
+ flash bank $@{_CHIPNAME@}_info.flash mdr 0x00000000 0x01000 \
+ 0 0 $_TARGETNAME 1 1 4
+@} else @{
+ flash bank $_CHIPNAME.flash mdr 0x00000000 0x20000 \
+ 0 0 $_TARGETNAME 0 32 4
+@}
+@end example
+@end deffn
+
+@deffn {Flash Driver} nrf51
+All members of the nRF51 microcontroller families from Nordic Semiconductor
+include internal flash and use ARM Cortex-M0 core.
+
+@example
+flash bank $_FLASHNAME nrf51 0 0x00000000 0 0 $_TARGETNAME
+@end example
+
+Some nrf51-specific commands are defined:
+
+@deffn Command {nrf51 mass_erase}
+Erases the contents of the code memory and user information
+configuration registers as well. It must be noted that this command
+works only for chips that do not have factory pre-programmed region 0
+code.
+@end deffn
+
+@end deffn
+
@deffn {Flash Driver} ocl
This driver is an implementation of the ``on chip flash loader''
protocol proposed by Pavel Chromy.
@end deffn
@end deffn
+@deffn {Flash Driver} sim3x
+All members of the SiM3 microcontroller family from Silicon Laboratories
+include internal flash and use ARM Cortex M3 cores. It supports both JTAG
+and SWD interface.
+The @var{sim3x} driver tries to probe the device to auto detect the MCU.
+If this failes, it will use the @var{size} parameter as the size of flash bank.
+
+@example
+flash bank $_FLASHNAME sim3x 0 $_CPUROMSIZE 0 0 $_TARGETNAME
+@end example
+
+There are 2 commands defined in the @var{sim3x} driver:
+
+@deffn Command {sim3x mass_erase}
+Erases the complete flash. This is used to unlock the flash.
+And this command is only possible when using the SWD interface.
+@end deffn
+
+@deffn Command {sim3x lock}
+Lock the flash. To unlock use the @command{sim3x mass_erase} command.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} stellaris
All members of the Stellaris LM3Sxxx, LM4x and Tiva C microcontroller
families from Texas Instruments include internal flash. The driver
@end deffn
@end deffn
-@deffn {Flash Driver} fm3
-All members of the FM3 microcontroller family from Fujitsu
-include internal flash and use ARM Cortex M3 cores.
-The @var{fm3} driver uses the @var{target} parameter to select the
-correct bank config, it can currently be one of the following:
-@code{mb9bfxx1.cpu}, @code{mb9bfxx2.cpu}, @code{mb9bfxx3.cpu},
-@code{mb9bfxx4.cpu}, @code{mb9bfxx5.cpu} or @code{mb9bfxx6.cpu}.
-
-@example
-flash bank $_FLASHNAME fm3 0 0 0 0 $_TARGETNAME
-@end example
-@end deffn
-
-@deffn {Flash Driver} sim3x
-All members of the SiM3 microcontroller family from Silicon Laboratories
-include internal flash and use ARM Cortex M3 cores. It supports both JTAG
-and SWD interface.
-The @var{sim3x} driver tries to probe the device to auto detect the MCU.
-If this failes, it will use the @var{size} parameter as the size of flash bank.
-
-@example
-flash bank $_FLASHNAME sim3x 0 $_CPUROMSIZE 0 0 $_TARGETNAME
-@end example
-
-There are 2 commands defined in the @var{sim3x} driver:
-
-@deffn Command {sim3x mass_erase}
-Erases the complete flash. This is used to unlock the flash.
-And this command is only possible when using the SWD interface.
-@end deffn
-
-@deffn Command {sim3x lock}
-Lock the flash. To unlock use the @command{sim3x mass_erase} command.
-@end deffn
-@end deffn
-
-@deffn {Flash Driver} nrf51
-All members of the nRF51 microcontroller families from Nordic Semiconductor
-include internal flash and use ARM Cortex-M0 core.
-
-@example
-flash bank $_FLASHNAME nrf51 0 0x00000000 0 0 $_TARGETNAME
-@end example
+@deffn {Flash Driver} xmc4xxx
+All members of the XMC4xxx microcontroller family from Infineon.
+This driver does not require the chip and bus width to be specified.
-Some nrf51-specific commands are defined:
+Some xmc4xxx-specific commands are defined:
-@deffn Command {nrf51 mass_erase}
-Erases the contents of the code memory and user information
-configuration registers as well. It must be noted that this command
-works only for chips that do not have factory pre-programmed region 0
-code.
+@deffn Command {xmc4xxx flash_password} bank_id passwd1 passwd2
+Saves flash protection passwords which are used to lock the user flash
@end deffn
+@deffn Command {xmc4xxx flash_unprotect} bank_id user_level[0-1]
+Removes Flash write protection from the selected user bank
@end deffn
-@deffn {Flash Driver} mdr
-This drivers handles the integrated NOR flash on Milandr Cortex-M
-based controllers. A known limitation is that the Info memory can't be
-read or verified as it's not memory mapped.
-
-@example
-flash bank <name> mdr <base> <size> \
- 0 0 <target#> @var{type} @var{page_count} @var{sec_count}
-@end example
-
-@itemize @bullet
-@item @var{type} - 0 for main memory, 1 for info memory
-@item @var{page_count} - total number of pages
-@item @var{sec_count} - number of sector per page count
-@end itemize
-
-Example usage:
-@example
-if @{ [info exists IMEMORY] && [string equal $IMEMORY true] @} @{
- flash bank $@{_CHIPNAME@}_info.flash mdr 0x00000000 0x01000 \
- 0 0 $_TARGETNAME 1 1 4
-@} else @{
- flash bank $_CHIPNAME.flash mdr 0x00000000 0x20000 \
- 0 0 $_TARGETNAME 0 32 4
-@}
-@end example
@end deffn
@section NAND Flash Commands
definition command, and may also define commands usable only with
that particular type of PLD.
-@deffn {FPGA Driver} virtex2
+@deffn {FPGA Driver} virtex2 [no_jstart]
Virtex-II is a family of FPGAs sold by Xilinx.
It supports the IEEE 1532 standard for In-System Configuration (ISC).
-No driver-specific PLD definition options are used,
-and one driver-specific command is defined.
+
+If @var{no_jstart} is non-zero, the JSTART instruction is not used after
+loading the bitstream. While required for Series2, Series3, and Series6, it
+breaks bitstream loading on Series7.
@deffn {Command} {virtex2 read_stat} num
Reads and displays the Virtex-II status register (STAT)
Defaulting to 0.
@end deffn
+@deffn Command {dap ti_be_32_quirks} [@option{enable}]
+Set/get quirks mode for TI TMS450/TMS570 processors
+Disabled by default
+@end deffn
+
+
+@subsection ARMv7-A specific commands
+@cindex Cortex-A
+
+@deffn Command {cortex_a cache_info}
+display information about target caches
+@end deffn
+
+@deffn Command {cortex_a dbginit}
+Initialize core debug
+Enables debug by unlocking the Software Lock and clearing sticky powerdown indications
+@end deffn
+
+@deffn Command {cortex_a smp_off}
+Disable SMP mode
+@end deffn
+
+@deffn Command {cortex_a smp_on}
+Enable SMP mode
+@end deffn
+
+@deffn Command {cortex_a smp_gdb} [core_id]
+Display/set the current core displayed in GDB
+@end deffn
+
+@deffn Command {cortex_a maskisr} [@option{on}|@option{off}]
+Selects whether interrupts will be processed when single stepping
+@end deffn
+
+@deffn Command {cache_config l2x} [base way]
+configure l2x cache
+@end deffn
+
+
+@subsection ARMv7-R specific commands
+@cindex Cortex-R
+
+@deffn Command {cortex_r dbginit}
+Initialize core debug
+Enables debug by unlocking the Software Lock and clearing sticky powerdown indications
+@end deffn
+
+@deffn Command {cortex_r maskisr} [@option{on}|@option{off}]
+Selects whether interrupts will be processed when single stepping
+@end deffn
+
+
@subsection ARMv7-M specific commands
@cindex tracing
@cindex SWO
@cindex ITM
@cindex ETM
-@deffn Command {tpiu config} (@option{disable} | ((@option{external} | @option{internal @var{filename}}) @
+@deffn Command {tpiu config} (@option{disable} | ((@option{external} | @option{internal (@var{filename} | -)}) @
(@option{sync @var{port_width}} | ((@option{manchester} | @option{uart}) @var{formatter_enable})) @
@var{TRACECLKIN_freq} [@var{trace_freq}]))
@item @option{internal @var{filename}} configure TPIU and debug adapter to
gather trace data and append it to @var{filename} (which can be
either a regular file or a named pipe);
+@item @option{internal -} configure TPIU and debug adapter to
+gather trace data, but not write to any file. Useful in conjunction with the @command{tcl_trace} command;
@item @option{sync @var{port_width}} use synchronous parallel trace output
mode, and set port width to @var{port_width};
@item @option{manchester} use asynchronous SWO mode with Manchester
@end deffn
+@section Tcl RPC server trace output
+@cindex RPC trace output
+
+Trace data is sent asynchronously to other commands being executed over
+the RPC server, so the port must be polled continuously.
+
+Target trace data is emitted as a Tcl associative array in the following format.
+
+@verbatim
+type target_trace data [trace-data-hex-encoded]
+@end verbatim
+
+@deffn {Command} tcl_trace [on/off]
+Toggle output of target trace data to the current Tcl RPC server.
+Only available from the Tcl RPC server.
+Defaults to off.
+
+See an example application here:
+@url{https://github.com/apmorton/OpenOcdTraceUtil} [OpenOcdTraceUtil]
+
+@end deffn
+
@node FAQ
@chapter FAQ
@cindex faq
projects / openocd / blobdiff