@itemize @bullet
@item Copyright @copyright{} 2008 The OpenOCD Project
@item Copyright @copyright{} 2007-2008 Spencer Oliver @email{spen@@spen-soft.co.uk}
-@item Copyright @copyright{} 2008 Oyvind Harboe @email{oyvind.harboe@@zylin.com}
+@item Copyright @copyright{} 2008-2010 Oyvind Harboe @email{oyvind.harboe@@zylin.com}
@item Copyright @copyright{} 2008 Duane Ellis @email{openocd@@duaneellis.com}
@item Copyright @copyright{} 2009-2010 David Brownell
@end itemize
other one is used to provide a debug adapter.
Also, some development boards integrate an FT2232 chip to serve as
-a built-in low coast debug adapter and usb-to-serial solution.
+a built-in low cost debug adapter and usb-to-serial solution.
@itemize @bullet
@item @b{usbjtag}
JIM-Tcl commands, and (older) the orginal command interpreter.
@item @b{Commands}
-@* At the OpenOCD telnet command line (or via the GDB mon command) one
+@* At the OpenOCD telnet command line (or via the GDB monitor command) one
can type a Tcl for() loop, set variables, etc.
Some of the commands documented in this guide are implemented
as Tcl scripts, from a @file{startup.tcl} file internal to the server.
@item @code{arm11} -- this is a generation of ARMv6 cores
@item @code{arm720t} -- this is an ARMv4 core with an MMU
@item @code{arm7tdmi} -- this is an ARMv4 core
-@item @code{arm920t} -- this is an ARMv5 core with an MMU
+@item @code{arm920t} -- this is an ARMv4 core with an MMU
@item @code{arm926ejs} -- this is an ARMv5 core with an MMU
@item @code{arm966e} -- this is an ARMv5 core
@item @code{arm9tdmi} -- this is an ARMv4 core
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
-@deffn Command {flash erase_address} [@option{pad}] address length
+@deffn Command {flash erase_address} [@option{pad}] [@option{unlock}] address length
Erase sectors starting at @var{address} for @var{length} bytes.
Unless @option{pad} is specified, @math{address} must begin a
flash sector, and @math{address + length - 1} must end a sector.
the specified length must stay within that bank.
As a special case, when @var{length} is zero and @var{address} is
the start of the bank, the whole flash is erased.
+If @option{unlock} is specified, then the flash is unprotected
+before erase starts.
@end deffn
@deffn Command {flash fillw} address word length
@deffn Command {flash info} num
Print info about flash bank @var{num}
The @var{num} parameter is a value shown by @command{flash banks}.
-The information includes per-sector protect status, which may be
-incorrect (outdated) unless you first issue a
-@command{flash protect_check num} command.
+This command will first query the hardware, it does not print cached
+and possibly stale information.
@end deffn
@anchor{flash protect}
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
-@deffn Command {flash protect_check} num
-Check protection state of sectors in flash bank @var{num}.
-The @var{num} parameter is a value shown by @command{flash banks}.
-@comment @option{flash erase_sector} using the same syntax.
-This updates the protection information displayed by @option{flash info}.
-(Code execution may have invalidated any state records kept by OpenOCD.)
-@end deffn
-
@anchor{Flash Driver List}
@section Flash Driver List
As noted above, the @command{flash bank} command requires a driver name,
@end deffn
@end deffn
+@deffn {Flash Driver} virtual
+This is a special driver that maps a previously defined bank to another
+address. All bank settings will be copied from the master physical bank.
+
+The @var{virtual} driver defines one mandatory parameters,
+
+@itemize
+@item @var{master_bank} The bank that this virtual address refers to.
+@end itemize
+
+So in the following example addresses 0xbfc00000 and 0x9fc00000 refer to
+the flash bank defined at address 0x1fc00000. Any cmds executed on
+the virtual banks are actually performed on the physical banks.
+@example
+flash bank $_FLASHNAME pic32mx 0x1fc00000 0 0 0 $_TARGETNAME
+flash bank vbank0 virtual 0xbfc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+flash bank vbank1 virtual 0x9fc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+@end example
+@end deffn
+
@subsection str9xpec driver
@cindex str9xpec
@end deffn
@anchor{load_image}
-@deffn Command {load_image} filename address [@option{bin}|@option{ihex}|@option{elf}] @option{min_addr} @option{max_length}]
+@deffn Command {load_image} filename address [[@option{bin}|@option{ihex}|@option{elf}] @option{min_addr} @option{max_length}]
Load image from file @var{filename} to target memory offset by @var{address} from its load address.
The file format may optionally be specified
(@option{bin}, @option{ihex}, or @option{elf}).