sunxi: Add Libre Computer Board ALL-H3-CC H5 ver.

[u-boot] / drivers / gpio / Kconfig

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index ffeda9425af13f07b10487e4a3110abff51d562e..b7e4ffb09d691c93934e7b5a3a01cfc9116e712e 100644 (file)
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -80,6 +80,13 @@ config IMX_RGPIO2P
        help
          This driver supports i.MX7ULP Rapid GPIO2P controller.
 
+config HSDK_CREG_GPIO
+       bool "HSDK CREG GPIO griver"
+       depends on DM_GPIO
+       default n
+       help
+         This driver supports CREG GPIOs on Synopsys HSDK SOC.
+
 config LPC32XX_GPIO
        bool "LPC32XX GPIO driver"
        depends on DM
@@ -101,6 +108,11 @@ config MSM_GPIO
          - APQ8016
          - MSM8916
 
+config MXC_GPIO
+       bool "Freescale/NXP MXC UART driver"
+       help
+         Support GPIO controllers on various i.MX platforms
+
 config OMAP_GPIO
        bool "TI OMAP GPIO driver"
        depends on ARCH_OMAP2PLUS
@@ -135,6 +147,12 @@ config PCF8575_GPIO
         Support for PCF8575 I2C 16-bit GPIO expander. Most of these
         chips are from NXP and TI.
 
+config RCAR_GPIO
+       bool "Renesas RCar GPIO driver"
+       depends on DM_GPIO && ARCH_RMOBILE
+       help
+         This driver supports the GPIO banks on Renesas RCar SoCs.
+
 config ROCKCHIP_GPIO
        bool "Rockchip GPIO driver"
        depends on DM_GPIO
@@ -165,6 +183,11 @@ config SANDBOX_GPIO_COUNT
          of 'anonymous' GPIOs that do not belong to any device or bank.
          Select a suitable value depending on your needs.
 
+config XILINX_GPIO
+       bool "Xilinx GPIO driver"
+       help
+         This config enable the Xilinx GPIO driver for Microblaze.
+
 config CMD_TCA642X
        bool "tca642x - Command to access tca642x state"
        help
@@ -211,7 +234,7 @@ config PIC32_GPIO
 
 config STM32F7_GPIO
        bool "ST STM32 GPIO driver"
-       depends on DM_GPIO && STM32
+       depends on DM_GPIO && (STM32 || ARCH_STM32MP)
        default y
        help
          Device model driver support for STM32 GPIO controller. It should be
@@ -263,11 +286,11 @@ config DM_PCA953X
          Now, max 24 bits chips and PCA953X compatible chips are
          supported
 
-config MPC85XX_GPIO
-       bool "Freescale MPC85XX GPIO driver"
+config MPC8XXX_GPIO
+       bool "Freescale MPC8XXX GPIO driver"
        depends on DM_GPIO
        help
-         This driver supports the built-in GPIO controller of MPC85XX CPUs.
+         This driver supports the built-in GPIO controller of MPC8XXX CPUs.
          Each GPIO bank is identified by its own entry in the device tree,
          i.e.
 
@@ -285,7 +308,4 @@ config MPC85XX_GPIO
          Aside from the standard functions of input/output mode, and output
          value setting, the open-drain feature, which can configure individual
          GPIOs to work as open-drain outputs, is supported.
-
-         The driver has been tested on MPC85XX, but it is likely that other
-         PowerQUICC III devices will work as well.
 endmenu