x86: fsp: Call fsp_init_phase_pci() in pci_uclass_post_probe()

[u-boot] / drivers / i2c / Kconfig

diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig
index 739badc3691401e725a4cfe43a8e5bad4b639f48..c40bd5c1e069749b5d06aac02b89e12f2d2789b6 100644 (file)
--- a/drivers/i2c/Kconfig
+++ b/drivers/i2c/Kconfig
@@ -1,3 +1,9 @@
+#
+# I2C subsystem configuration
+#
+
+menu "I2C support"
+
 config DM_I2C
        bool "Enable Driver Model for I2C drivers"
        depends on DM
@@ -19,6 +25,30 @@ config DM_I2C_COMPAT
          to convert all code for a board in a single commit. It should not
          be enabled for any board in an official release.
 
+config I2C_CROS_EC_TUNNEL
+       tristate "Chrome OS EC tunnel I2C bus"
+       depends on CROS_EC
+       help
+         This provides an I2C bus that will tunnel i2c commands through to
+         the other side of the Chrome OS EC to the I2C bus connected there.
+         This will work whatever the interface used to talk to the EC (SPI,
+         I2C or LPC). Some Chromebooks use this when the hardware design
+         does not allow direct access to the main PMIC from the AP.
+
+config I2C_CROS_EC_LDO
+       bool "Provide access to LDOs on the Chrome OS EC"
+       depends on CROS_EC
+       ---help---
+       On many Chromebooks the main PMIC is inaccessible to the AP. This is
+       often dealt with by using an I2C pass-through interface provided by
+       the EC. On some unfortunate models (e.g. Spring) the pass-through
+       is not available, and an LDO message is available instead. This
+       option enables a driver which provides very basic access to those
+       regulators, via the EC. We implement this as an I2C bus which
+       emulates just the TPS65090 messages we know about. This is done to
+       avoid duplicating the logic in the TPS65090 regulator driver for
+       enabling/disabling an LDO.
+
 config DM_I2C_GPIO
        bool "Enable Driver Model for software emulated I2C bus driver"
        depends on DM_I2C && DM_GPIO
@@ -28,18 +58,52 @@ config DM_I2C_GPIO
          bindings are supported.
          Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
 
+config SYS_I2C_SANDBOX
+       bool "Sandbox I2C driver"
+       depends on SANDBOX && DM_I2C
+       help
+         Enable I2C support for sandbox. This is an emulation of a real I2C
+         bus. Devices can be attached to the bus using the device tree
+         which specifies the driver to use. As an example, see this device
+         tree fragment from sandbox.dts. It shows that the I2C bus has a
+         single EEPROM at address 0x2c (7-bit address) which is emulated by
+         the driver for "sandbox,i2c-eeprom", which is in
+         drivers/misc/i2c_eeprom_emul.c.
+
+         i2c@0 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0>;
+               compatible = "sandbox,i2c";
+               clock-frequency = <400000>;
+               eeprom@2c {
+                       reg = <0x2c>;
+                       compatible = "i2c-eeprom";
+                       emul {
+                               compatible = "sandbox,i2c-eeprom";
+                               sandbox,filename = "i2c.bin";
+                               sandbox,size = <128>;
+                       };
+               };
+       };
+
+
 config SYS_I2C_UNIPHIER
        bool "UniPhier I2C driver"
        depends on ARCH_UNIPHIER && DM_I2C
        default y
        help
-         Support for Panasonic UniPhier I2C controller driver.  This I2C
-         controller is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
+         Support for UniPhier I2C controller driver.  This I2C controller
+         is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
 
 config SYS_I2C_UNIPHIER_F
        bool "UniPhier FIFO-builtin I2C driver"
        depends on ARCH_UNIPHIER && DM_I2C
        default y
        help
-         Support for Panasonic UniPhier FIFO-builtin I2C controller driver.
+         Support for UniPhier FIFO-builtin I2C controller driver.
          This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
+
+source "drivers/i2c/muxes/Kconfig"
+
+endmenu