#include <asm/io.h>
/*
- * include a file that will provide CONFIG_I2C_MVTWSI_BASE
+ * include a file that will provide CONFIG_I2C_MVTWSI_BASE*
* and possibly other settings
*/
#if defined(CONFIG_ORION5X)
#include <asm/arch/orion5x.h>
-#elif defined(CONFIG_KIRKWOOD)
-#include <asm/arch/kirkwood.h>
+#elif (defined(CONFIG_KIRKWOOD) || defined(CONFIG_ARMADA_XP))
+#include <asm/arch/soc.h>
+#elif defined(CONFIG_SUNXI)
+#include <asm/arch/i2c.h>
#else
#error Driver mvtwsi not supported by SoC or board
#endif
* TWSI register structure
*/
+#ifdef CONFIG_SUNXI
+
+struct mvtwsi_registers {
+ u32 slave_address;
+ u32 xtnd_slave_addr;
+ u32 data;
+ u32 control;
+ u32 status;
+ u32 baudrate;
+ u32 soft_reset;
+};
+
+#else
+
struct mvtwsi_registers {
u32 slave_address;
u32 data;
u32 soft_reset;
};
+#endif
+
/*
* Control register fields
*/
#define MVTWSI_STATUS_IDLE 0xF8
/*
- * The single instance of the controller we'll be dealing with
+ * MVTWSI controller base
*/
-static struct mvtwsi_registers *twsi =
- (struct mvtwsi_registers *) CONFIG_I2C_MVTWSI_BASE;
+static struct mvtwsi_registers *twsi_get_base(struct i2c_adapter *adap)
+{
+ switch (adap->hwadapnr) {
+#ifdef CONFIG_I2C_MVTWSI_BASE0
+ case 0:
+ return (struct mvtwsi_registers *) CONFIG_I2C_MVTWSI_BASE0;
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE1
+ case 1:
+ return (struct mvtwsi_registers *) CONFIG_I2C_MVTWSI_BASE1;
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE2
+ case 2:
+ return (struct mvtwsi_registers *) CONFIG_I2C_MVTWSI_BASE2;
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE3
+ case 3:
+ return (struct mvtwsi_registers *) CONFIG_I2C_MVTWSI_BASE3;
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE4
+ case 4:
+ return (struct mvtwsi_registers *) CONFIG_I2C_MVTWSI_BASE4;
+#endif
+ default:
+ printf("Missing mvtwsi controller %d base\n", adap->hwadapnr);
+ break;
+ }
+
+ return NULL;
+}
/*
* Returned statuses are 0 for success and nonzero otherwise.
* Wait for IFLG to raise, or return 'timeout'; then if status is as expected,
* return 0 (ok) or return 'wrong status'.
*/
-static int twsi_wait(int expected_status)
+static int twsi_wait(struct i2c_adapter *adap, int expected_status)
{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
int control, status;
int timeout = 1000;
* Assert the START condition, either in a single I2C transaction
* or inside back-to-back ones (repeated starts).
*/
-static int twsi_start(int expected_status)
+static int twsi_start(struct i2c_adapter *adap, int expected_status)
{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
+
/* globally set TWSIEN in case it was not */
twsi_control_flags |= MVTWSI_CONTROL_TWSIEN;
/* assert START */
writel(twsi_control_flags | MVTWSI_CONTROL_START, &twsi->control);
/* wait for controller to process START */
- return twsi_wait(expected_status);
+ return twsi_wait(adap, expected_status);
}
/*
* Send a byte (i2c address or data).
*/
-static int twsi_send(u8 byte, int expected_status)
+static int twsi_send(struct i2c_adapter *adap, u8 byte, int expected_status)
{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
+
/* put byte in data register for sending */
writel(byte, &twsi->data);
/* clear any pending interrupt -- that'll cause sending */
writel(twsi_control_flags, &twsi->control);
/* wait for controller to receive byte and check ACK */
- return twsi_wait(expected_status);
+ return twsi_wait(adap, expected_status);
}
/*
* Receive a byte.
* Global mvtwsi_control_flags variable says if we should ack or nak.
*/
-static int twsi_recv(u8 *byte)
+static int twsi_recv(struct i2c_adapter *adap, u8 *byte)
{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
int expected_status, status;
/* compute expected status based on ACK bit in global control flags */
/* acknowledge *previous state* and launch receive */
writel(twsi_control_flags, &twsi->control);
/* wait for controller to receive byte and assert ACK or NAK */
- status = twsi_wait(expected_status);
+ status = twsi_wait(adap, expected_status);
/* if we did receive expected byte then store it */
if (status == 0)
*byte = readl(&twsi->data);
* Assert the STOP condition.
* This is also used to force the bus back in idle (SDA=SCL=1).
*/
-static int twsi_stop(int status)
+static int twsi_stop(struct i2c_adapter *adap, int status)
{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
int control, stop_status;
int timeout = 1000;
return status;
}
-/*
- * Ugly formula to convert m and n values to a frequency comes from
- * TWSI specifications
- */
-
-#define TWSI_FREQUENCY(m, n) \
- ((u8) (CONFIG_SYS_TCLK / (10 * (m + 1) * 2 * (1 << n))))
-
-/*
- * These are required to be reprogrammed before enabling the controller
- * because a reset loses them.
- * Default values come from the spec, but a twsi_reset will change them.
- * twsi_slave_address left uninitialized lest checkpatch.pl complains.
- */
-
-/* Baudrate generator: m (bits 7..4) =4, n (bits 3..0) =4 */
-static u8 twsi_baud_rate = 0x44; /* baudrate at controller reset */
-/* Default frequency corresponding to default m=4, n=4 */
-static u8 twsi_actual_speed = TWSI_FREQUENCY(4, 4);
-/* Default slave address is 0 (so is an uninitialized static) */
-static u8 twsi_slave_address;
+static unsigned int twsi_calc_freq(const int n, const int m)
+{
+#ifdef CONFIG_SUNXI
+ return CONFIG_SYS_TCLK / (10 * (m + 1) * (1 << n));
+#else
+ return CONFIG_SYS_TCLK / (10 * (m + 1) * (2 << n));
+#endif
+}
/*
* Reset controller.
- * Called at end of i2c_init unsuccessful i2c transactions.
* Controller reset also resets the baud rate and slave address, so
- * re-establish them.
+ * they must be re-established afterwards.
*/
-static void twsi_reset(void)
+static void twsi_reset(struct i2c_adapter *adap)
{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
/* ensure controller will be enabled by any twsi*() function */
twsi_control_flags = MVTWSI_CONTROL_TWSIEN;
/* reset controller */
writel(0, &twsi->soft_reset);
/* wait 2 ms -- this is what the Marvell LSP does */
udelay(20000);
- /* set baud rate */
- writel(twsi_baud_rate, &twsi->baudrate);
- /* set slave address even though we don't use it */
- writel(twsi_slave_address, &twsi->slave_address);
- writel(0, &twsi->xtnd_slave_addr);
- /* assert STOP but don't care for the result */
- (void) twsi_stop(0);
}
/*
* I2C init called by cmd_i2c when doing 'i2c reset'.
* Sets baud to the highest possible value not exceeding requested one.
*/
-void i2c_init(int requested_speed, int slaveadd)
+static unsigned int twsi_i2c_set_bus_speed(struct i2c_adapter *adap,
+ unsigned int requested_speed)
{
- int tmp_speed, highest_speed, n, m;
- int baud = 0x44; /* baudrate at controller reset */
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
+ unsigned int tmp_speed, highest_speed, n, m;
+ unsigned int baud = 0x44; /* baudrate at controller reset */
/* use actual speed to collect progressively higher values */
highest_speed = 0;
/* compute m, n setting for highest speed not above requested speed */
for (n = 0; n < 8; n++) {
for (m = 0; m < 16; m++) {
- tmp_speed = TWSI_FREQUENCY(m, n);
+ tmp_speed = twsi_calc_freq(n, m);
if ((tmp_speed <= requested_speed)
&& (tmp_speed > highest_speed)) {
highest_speed = tmp_speed;
}
}
}
- /* save baud rate and slave for later calls to twsi_reset */
- twsi_baud_rate = baud;
- twsi_actual_speed = highest_speed;
- twsi_slave_address = slaveadd;
+ writel(baud, &twsi->baudrate);
+ return 0;
+}
+
+static void twsi_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
+{
+ struct mvtwsi_registers *twsi = twsi_get_base(adap);
+
/* reset controller */
- twsi_reset();
+ twsi_reset(adap);
+ /* set speed */
+ twsi_i2c_set_bus_speed(adap, speed);
+ /* set slave address even though we don't use it */
+ writel(slaveadd, &twsi->slave_address);
+ writel(0, &twsi->xtnd_slave_addr);
+ /* assert STOP but don't care for the result */
+ (void) twsi_stop(adap, 0);
}
/*
* Common to i2c_probe, i2c_read and i2c_write.
* Expected address status will derive from direction bit (bit 0) in addr.
*/
-static int i2c_begin(int expected_start_status, u8 addr)
+static int i2c_begin(struct i2c_adapter *adap, int expected_start_status,
+ u8 addr)
{
int status, expected_addr_status;
else /* writing */
expected_addr_status = MVTWSI_STATUS_ADDR_W_ACK;
/* assert START */
- status = twsi_start(expected_start_status);
+ status = twsi_start(adap, expected_start_status);
/* send out the address if the start went well */
if (status == 0)
- status = twsi_send(addr, expected_addr_status);
+ status = twsi_send(adap, addr, expected_addr_status);
/* return ok or status of first failure to caller */
return status;
}
* I2C probe called by cmd_i2c when doing 'i2c probe'.
* Begin read, nak data byte, end.
*/
-int i2c_probe(uchar chip)
+static int twsi_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
u8 dummy_byte;
int status;
/* begin i2c read */
- status = i2c_begin(MVTWSI_STATUS_START, (chip << 1) | 1);
+ status = i2c_begin(adap, MVTWSI_STATUS_START, (chip << 1) | 1);
/* dummy read was accepted: receive byte but NAK it. */
if (status == 0)
- status = twsi_recv(&dummy_byte);
+ status = twsi_recv(adap, &dummy_byte);
/* Stop transaction */
- twsi_stop(0);
+ twsi_stop(adap, 0);
/* return 0 or status of first failure */
return status;
}
* cmd_eeprom, so we have to choose here, and for the moment that'll be
* a repeated start without a preceding stop.
*/
-int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
+static int twsi_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *data, int length)
{
int status;
/* begin i2c write to send the address bytes */
- status = i2c_begin(MVTWSI_STATUS_START, (dev << 1));
+ status = i2c_begin(adap, MVTWSI_STATUS_START, (chip << 1));
/* send addr bytes */
while ((status == 0) && alen--)
- status = twsi_send(addr >> (8*alen),
+ status = twsi_send(adap, addr >> (8*alen),
MVTWSI_STATUS_DATA_W_ACK);
/* begin i2c read to receive eeprom data bytes */
if (status == 0)
- status = i2c_begin(
- MVTWSI_STATUS_REPEATED_START, (dev << 1) | 1);
+ status = i2c_begin(adap, MVTWSI_STATUS_REPEATED_START,
+ (chip << 1) | 1);
/* prepare ACK if at least one byte must be received */
if (length > 0)
twsi_control_flags |= MVTWSI_CONTROL_ACK;
if (length == 0)
twsi_control_flags &= ~MVTWSI_CONTROL_ACK;
/* read current byte */
- status = twsi_recv(data++);
+ status = twsi_recv(adap, data++);
}
/* Stop transaction */
- status = twsi_stop(status);
+ status = twsi_stop(adap, status);
/* return 0 or status of first failure */
return status;
}
* I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c
* Begin write, send address byte(s), send data bytes, end.
*/
-int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
+static int twsi_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *data, int length)
{
int status;
/* begin i2c write to send the eeprom adress bytes then data bytes */
- status = i2c_begin(MVTWSI_STATUS_START, (dev << 1));
+ status = i2c_begin(adap, MVTWSI_STATUS_START, (chip << 1));
/* send addr bytes */
while ((status == 0) && alen--)
- status = twsi_send(addr >> (8*alen),
+ status = twsi_send(adap, addr >> (8*alen),
MVTWSI_STATUS_DATA_W_ACK);
/* send data bytes */
while ((status == 0) && (length-- > 0))
- status = twsi_send(*(data++), MVTWSI_STATUS_DATA_W_ACK);
+ status = twsi_send(adap, *(data++), MVTWSI_STATUS_DATA_W_ACK);
/* Stop transaction */
- status = twsi_stop(status);
+ status = twsi_stop(adap, status);
/* return 0 or status of first failure */
return status;
}
-/*
- * Bus set routine: we only support bus 0.
- */
-int i2c_set_bus_num(unsigned int bus)
-{
- if (bus > 0) {
- return -1;
- }
- return 0;
-}
+#ifdef CONFIG_I2C_MVTWSI_BASE0
+U_BOOT_I2C_ADAP_COMPLETE(twsi0, twsi_i2c_init, twsi_i2c_probe,
+ twsi_i2c_read, twsi_i2c_write,
+ twsi_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 0)
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE1
+U_BOOT_I2C_ADAP_COMPLETE(twsi1, twsi_i2c_init, twsi_i2c_probe,
+ twsi_i2c_read, twsi_i2c_write,
+ twsi_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 1)
-/*
- * Bus get routine: hard-return bus 0.
- */
-unsigned int i2c_get_bus_num(void)
-{
- return 0;
-}
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE2
+U_BOOT_I2C_ADAP_COMPLETE(twsi2, twsi_i2c_init, twsi_i2c_probe,
+ twsi_i2c_read, twsi_i2c_write,
+ twsi_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 2)
+
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE3
+U_BOOT_I2C_ADAP_COMPLETE(twsi3, twsi_i2c_init, twsi_i2c_probe,
+ twsi_i2c_read, twsi_i2c_write,
+ twsi_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 3)
+
+#endif
+#ifdef CONFIG_I2C_MVTWSI_BASE4
+U_BOOT_I2C_ADAP_COMPLETE(twsi4, twsi_i2c_init, twsi_i2c_probe,
+ twsi_i2c_read, twsi_i2c_write,
+ twsi_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 4)
+
+#endif
projects / u-boot / blobdiff