ddr: altera: silence PHY calibration unless in debug mode

[u-boot] / drivers / mmc / Kconfig

diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index c34ab219e88498c764ed5bae0e3adc024437add9..bc29611d783be4788777ef70e7ed14cbe1c8004b 100644 (file)
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -10,6 +10,18 @@ config MMC
          If you want MMC/SD/SDIO support, you should say Y here and
          also to your specific host controller driver.
 
+config MMC_WRITE
+       bool "support for MMC/SD write operations"
+       depends on MMC
+       default y
+       help
+         Enable write access to MMC and SD Cards
+
+config MMC_BROKEN_CD
+       bool "Poll for broken card detection case"
+       help
+         If card  detection feature is broken, just poll to detect.
+
 config DM_MMC
        bool "Enable MMC controllers using Driver Model"
        depends on DM
@@ -51,6 +63,59 @@ config MMC_QUIRKS
          are enabled by default, other may require additionnal flags or are
          enabled by the host driver.
 
+config MMC_HW_PARTITIONING
+       bool "Support for HW partitioning command(eMMC)"
+       default y
+       help
+         This adds a command and an API to do hardware partitioning on eMMC
+         devices.
+
+config MMC_IO_VOLTAGE
+       bool "Support IO voltage configuration"
+       help
+         IO voltage configuration allows selecting the voltage level of the IO
+         lines (not the level of main supply). This is required for UHS
+         support. For eMMC this not mandatory, but not enabling this option may
+         prevent the driver of using the faster modes.
+
+config SPL_MMC_IO_VOLTAGE
+       bool "Support IO voltage configuration in SPL"
+       default n
+       help
+         IO voltage configuration allows selecting the voltage level of the IO
+         lines (not the level of main supply). This is required for UHS
+         support. For eMMC this not mandatory, but not enabling this option may
+         prevent the driver of using the faster modes.
+
+config MMC_UHS_SUPPORT
+       bool "enable UHS support"
+       depends on MMC_IO_VOLTAGE
+       help
+         The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
+         cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
+         frequency can go up to 208MHz (SDR104)
+
+config SPL_MMC_UHS_SUPPORT
+       bool "enable UHS support in SPL"
+       depends on SPL_MMC_IO_VOLTAGE
+       help
+         The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
+         cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
+         frequency can go up to 208MHz (SDR104)
+
+config MMC_HS200_SUPPORT
+       bool "enable HS200 support"
+       help
+         The HS200 mode is support by some eMMC. The bus frequency is up to
+         200MHz. This mode requires tuning the IO.
+
+
+config SPL_MMC_HS200_SUPPORT
+       bool "enable HS200 support in SPL"
+       help
+         The HS200 mode is support by some eMMC. The bus frequency is up to
+         200MHz. This mode requires tuning the IO.
+
 config MMC_VERBOSE
        bool "Output more information about the MMC"
        default y