+// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2012 SAMSUNG Electronics
* Jaehoon Chung <jh80.chung@samsung.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <dwmmc.h>
#include <fdtdec.h>
-#include <libfdt.h>
+#include <linux/libfdt.h>
#include <malloc.h>
+#include <errno.h>
#include <asm/arch/dwmmc.h>
#include <asm/arch/clk.h>
#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <asm/gpio.h>
#define DWMMC_MAX_CH_NUM 4
#define DWMMC_MAX_FREQ 52000000
#define DWMMC_MIN_FREQ 400000
-#define DWMMC_MMC0_CLKSEL_VAL 0x03030001
-#define DWMMC_MMC2_CLKSEL_VAL 0x03020001
+#define DWMMC_MMC0_SDR_TIMING_VAL 0x03030001
+#define DWMMC_MMC2_SDR_TIMING_VAL 0x03020001
+
+#ifdef CONFIG_DM_MMC
+#include <dm.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+struct exynos_mmc_plat {
+ struct mmc_config cfg;
+ struct mmc mmc;
+};
+#endif
+
+/* Exynos implmentation specific drver private data */
+struct dwmci_exynos_priv_data {
+#ifdef CONFIG_DM_MMC
+ struct dwmci_host host;
+#endif
+ u32 sdr_timing;
+};
/*
* Function used as callback function to initialise the
*/
static void exynos_dwmci_clksel(struct dwmci_host *host)
{
- dwmci_writel(host, DWMCI_CLKSEL, host->clksel_val);
+ struct dwmci_exynos_priv_data *priv = host->priv;
+
+ dwmci_writel(host, DWMCI_CLKSEL, priv->sdr_timing);
}
-unsigned int exynos_dwmci_get_clk(int dev_index)
+unsigned int exynos_dwmci_get_clk(struct dwmci_host *host, uint freq)
{
- return get_mmc_clk(dev_index);
+ unsigned long sclk;
+ int8_t clk_div;
+
+ /*
+ * Since SDCLKIN is divided inside controller by the DIVRATIO
+ * value set in the CLKSEL register, we need to use the same output
+ * clock value to calculate the CLKDIV value.
+ * as per user manual:cclk_in = SDCLKIN / (DIVRATIO + 1)
+ */
+ clk_div = ((dwmci_readl(host, DWMCI_CLKSEL) >> DWMCI_DIVRATIO_BIT)
+ & DWMCI_DIVRATIO_MASK) + 1;
+ sclk = get_mmc_clk(host->dev_index);
+
+ /*
+ * Assume to know divider value.
+ * When clock unit is broken, need to set "host->div"
+ */
+ return sclk / clk_div / (host->div + 1);
}
static void exynos_dwmci_board_init(struct dwmci_host *host)
{
+ struct dwmci_exynos_priv_data *priv = host->priv;
+
if (host->quirks & DWMCI_QUIRK_DISABLE_SMU) {
dwmci_writel(host, EMMCP_MPSBEGIN0, 0);
dwmci_writel(host, EMMCP_SEND0, 0);
MPSCTRL_NON_SECURE_READ_BIT |
MPSCTRL_NON_SECURE_WRITE_BIT | MPSCTRL_VALID);
}
+
+ /* Set to timing value at initial time */
+ if (priv->sdr_timing)
+ exynos_dwmci_clksel(host);
}
-/*
- * This function adds the mmc channel to be registered with mmc core.
- * index - mmc channel number.
- * regbase - register base address of mmc channel specified in 'index'.
- * bus_width - operating bus width of mmc channel specified in 'index'.
- * clksel - value to be written into CLKSEL register in case of FDT.
- * NULL in case od non-FDT.
- */
-int exynos_dwmci_add_port(int index, u32 regbase, int bus_width, u32 clksel)
+static int exynos_dwmci_core_init(struct dwmci_host *host)
{
- struct dwmci_host *host = NULL;
unsigned int div;
unsigned long freq, sclk;
- host = malloc(sizeof(struct dwmci_host));
- if (!host) {
- printf("dwmci_host malloc fail!\n");
- return 1;
- }
+
+ if (host->bus_hz)
+ freq = host->bus_hz;
+ else
+ freq = DWMMC_MAX_FREQ;
+
/* request mmc clock vlaue of 52MHz. */
- freq = 52000000;
- sclk = get_mmc_clk(index);
+ sclk = get_mmc_clk(host->dev_index);
div = DIV_ROUND_UP(sclk, freq);
/* set the clock divisor for mmc */
- set_mmc_clk(index, div);
+ set_mmc_clk(host->dev_index, div);
host->name = "EXYNOS DWMMC";
- host->ioaddr = (void *)regbase;
- host->buswidth = bus_width;
#ifdef CONFIG_EXYNOS5420
host->quirks = DWMCI_QUIRK_DISABLE_SMU;
#endif
host->board_init = exynos_dwmci_board_init;
- if (clksel) {
- host->clksel_val = clksel;
- } else {
- if (0 == index)
- host->clksel_val = DWMMC_MMC0_CLKSEL_VAL;
- if (2 == index)
- host->clksel_val = DWMMC_MMC2_CLKSEL_VAL;
- }
-
+ host->caps = MMC_MODE_DDR_52MHz;
host->clksel = exynos_dwmci_clksel;
- host->dev_index = index;
host->get_mmc_clk = exynos_dwmci_get_clk;
+
+#ifndef CONFIG_DM_MMC
/* Add the mmc channel to be registered with mmc core */
if (add_dwmci(host, DWMMC_MAX_FREQ, DWMMC_MIN_FREQ)) {
- debug("dwmmc%d registration failed\n", index);
+ printf("DWMMC%d registration failed\n", host->dev_index);
return -1;
}
+#endif
+
return 0;
}
-#ifdef CONFIG_OF_CONTROL
-int exynos_dwmmc_init(const void *blob)
+static struct dwmci_host dwmci_host[DWMMC_MAX_CH_NUM];
+
+static int do_dwmci_init(struct dwmci_host *host)
{
- int index, bus_width;
- int node_list[DWMMC_MAX_CH_NUM];
- int err = 0, dev_id, flag, count, i;
- u32 clksel_val, base, timing[3];
+ int flag, err;
- count = fdtdec_find_aliases_for_id(blob, "mmc",
- COMPAT_SAMSUNG_EXYNOS5_DWMMC, node_list,
- DWMMC_MAX_CH_NUM);
+ flag = host->buswidth == 8 ? PINMUX_FLAG_8BIT_MODE : PINMUX_FLAG_NONE;
+ err = exynos_pinmux_config(host->dev_id, flag);
+ if (err) {
+ printf("DWMMC%d not configure\n", host->dev_index);
+ return err;
+ }
- for (i = 0; i < count; i++) {
- int node = node_list[i];
+ return exynos_dwmci_core_init(host);
+}
- if (node <= 0)
- continue;
+static int exynos_dwmci_get_config(const void *blob, int node,
+ struct dwmci_host *host)
+{
+ int err = 0;
+ u32 base, timing[3];
+ struct dwmci_exynos_priv_data *priv;
- /* Extract device id for each mmc channel */
- dev_id = pinmux_decode_periph_id(blob, node);
+ priv = malloc(sizeof(struct dwmci_exynos_priv_data));
+ if (!priv) {
+ pr_err("dwmci_exynos_priv_data malloc fail!\n");
+ return -ENOMEM;
+ }
- /* Get the bus width from the device node */
- bus_width = fdtdec_get_int(blob, node, "samsung,bus-width", 0);
- if (bus_width <= 0) {
- debug("DWMMC: Can't get bus-width\n");
- return -1;
- }
- if (8 == bus_width)
- flag = PINMUX_FLAG_8BIT_MODE;
- else
- flag = PINMUX_FLAG_NONE;
+ /* Extract device id for each mmc channel */
+ host->dev_id = pinmux_decode_periph_id(blob, node);
- /* config pinmux for each mmc channel */
- err = exynos_pinmux_config(dev_id, flag);
- if (err) {
- debug("DWMMC not configured\n");
- return err;
- }
+ host->dev_index = fdtdec_get_int(blob, node, "index", host->dev_id);
+ if (host->dev_index == host->dev_id)
+ host->dev_index = host->dev_id - PERIPH_ID_SDMMC0;
- index = dev_id - PERIPH_ID_SDMMC0;
+ if (host->dev_index > 4) {
+ printf("DWMMC%d: Can't get the dev index\n", host->dev_index);
+ free(priv);
+ return -EINVAL;
+ }
- /* Get the base address from the device node */
- base = fdtdec_get_addr(blob, node, "reg");
- if (!base) {
- debug("DWMMC: Can't get base address\n");
- return -1;
- }
- /* Extract the timing info from the node */
- err = fdtdec_get_int_array(blob, node, "samsung,timing",
- timing, 3);
+ /* Get the bus width from the device node (Default is 4bit buswidth) */
+ host->buswidth = fdtdec_get_int(blob, node, "samsung,bus-width", 4);
+
+ /* Set the base address from the device node */
+ base = fdtdec_get_addr(blob, node, "reg");
+ if (!base) {
+ printf("DWMMC%d: Can't get base address\n", host->dev_index);
+ free(priv);
+ return -EINVAL;
+ }
+ host->ioaddr = (void *)base;
+
+ /* Extract the timing info from the node */
+ err = fdtdec_get_int_array(blob, node, "samsung,timing", timing, 3);
+ if (err) {
+ printf("DWMMC%d: Can't get sdr-timings for devider\n",
+ host->dev_index);
+ free(priv);
+ return -EINVAL;
+ }
+
+ priv->sdr_timing = (DWMCI_SET_SAMPLE_CLK(timing[0]) |
+ DWMCI_SET_DRV_CLK(timing[1]) |
+ DWMCI_SET_DIV_RATIO(timing[2]));
+
+ /* sdr_timing didn't assigned anything, use the default value */
+ if (!priv->sdr_timing) {
+ if (host->dev_index == 0)
+ priv->sdr_timing = DWMMC_MMC0_SDR_TIMING_VAL;
+ else if (host->dev_index == 2)
+ priv->sdr_timing = DWMMC_MMC2_SDR_TIMING_VAL;
+ }
+
+ host->fifoth_val = fdtdec_get_int(blob, node, "fifoth_val", 0);
+ host->bus_hz = fdtdec_get_int(blob, node, "bus_hz", 0);
+ host->div = fdtdec_get_int(blob, node, "div", 0);
+
+ host->priv = priv;
+
+ return 0;
+}
+
+static int exynos_dwmci_process_node(const void *blob,
+ int node_list[], int count)
+{
+ struct dwmci_host *host;
+ int i, node, err;
+
+ for (i = 0; i < count; i++) {
+ node = node_list[i];
+ if (node <= 0)
+ continue;
+ host = &dwmci_host[i];
+ err = exynos_dwmci_get_config(blob, node, host);
if (err) {
- debug("Can't get sdr-timings for divider\n");
- return -1;
+ printf("%s: failed to decode dev %d\n", __func__, i);
+ return err;
}
- clksel_val = (DWMCI_SET_SAMPLE_CLK(timing[0]) |
- DWMCI_SET_DRV_CLK(timing[1]) |
- DWMCI_SET_DIV_RATIO(timing[2]));
- /* Initialise each mmc channel */
- err = exynos_dwmci_add_port(index, base, bus_width, clksel_val);
- if (err)
- debug("dwmmc Channel-%d init failed\n", index);
+ do_dwmci_init(host);
}
return 0;
}
+
+int exynos_dwmmc_init(const void *blob)
+{
+ int node_list[DWMMC_MAX_CH_NUM];
+ int boot_dev_node;
+ int err = 0, count;
+
+ count = fdtdec_find_aliases_for_id(blob, "mmc",
+ COMPAT_SAMSUNG_EXYNOS_DWMMC, node_list,
+ DWMMC_MAX_CH_NUM);
+
+ /* For DWMMC always set boot device as mmc 0 */
+ if (count >= 3 && get_boot_mode() == BOOT_MODE_SD) {
+ boot_dev_node = node_list[2];
+ node_list[2] = node_list[0];
+ node_list[0] = boot_dev_node;
+ }
+
+ err = exynos_dwmci_process_node(blob, node_list, count);
+
+ return err;
+}
+
+#ifdef CONFIG_DM_MMC
+static int exynos_dwmmc_probe(struct udevice *dev)
+{
+ struct exynos_mmc_plat *plat = dev_get_platdata(dev);
+ struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
+ struct dwmci_exynos_priv_data *priv = dev_get_priv(dev);
+ struct dwmci_host *host = &priv->host;
+ int err;
+
+ err = exynos_dwmci_get_config(gd->fdt_blob, dev_of_offset(dev), host);
+ if (err)
+ return err;
+ err = do_dwmci_init(host);
+ if (err)
+ return err;
+
+ dwmci_setup_cfg(&plat->cfg, host, DWMMC_MAX_FREQ, DWMMC_MIN_FREQ);
+ host->mmc = &plat->mmc;
+ host->mmc->priv = &priv->host;
+ host->priv = dev;
+ upriv->mmc = host->mmc;
+
+ return dwmci_probe(dev);
+}
+
+static int exynos_dwmmc_bind(struct udevice *dev)
+{
+ struct exynos_mmc_plat *plat = dev_get_platdata(dev);
+
+ return dwmci_bind(dev, &plat->mmc, &plat->cfg);
+}
+
+static const struct udevice_id exynos_dwmmc_ids[] = {
+ { .compatible = "samsung,exynos4412-dw-mshc" },
+ { }
+};
+
+U_BOOT_DRIVER(exynos_dwmmc_drv) = {
+ .name = "exynos_dwmmc",
+ .id = UCLASS_MMC,
+ .of_match = exynos_dwmmc_ids,
+ .bind = exynos_dwmmc_bind,
+ .ops = &dm_dwmci_ops,
+ .probe = exynos_dwmmc_probe,
+ .priv_auto_alloc_size = sizeof(struct dwmci_exynos_priv_data),
+ .platdata_auto_alloc_size = sizeof(struct exynos_mmc_plat),
+};
#endif