static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2,
0x97, 0x79, 0xe5, 0x24, 0xb5};
#endif
-static uint8_t cs;
+static uint8_t cs_next;
static __maybe_unused struct nand_ecclayout omap_ecclayout;
+#if defined(CONFIG_NAND_OMAP_GPMC_WSCFG)
+static const int8_t wscfg[CONFIG_SYS_MAX_NAND_DEVICE] =
+ { CONFIG_NAND_OMAP_GPMC_WSCFG };
+#else
+/* wscfg is preset to zero since its a static variable */
+static const int8_t wscfg[CONFIG_SYS_MAX_NAND_DEVICE];
+#endif
+
+/*
+ * Driver configurations
+ */
+struct omap_nand_info {
+ struct bch_control *control;
+ enum omap_ecc ecc_scheme;
+ uint8_t cs;
+ uint8_t ws; /* wait status pin (0,1) */
+};
+
+/* We are wasting a bit of memory but al least we are safe */
+static struct omap_nand_info omap_nand_info[GPMC_MAX_CS];
+
/*
* omap_nand_hwcontrol - Set the address pointers corretly for the
* following address/data/command operation
uint32_t ctrl)
{
register struct nand_chip *this = mtd->priv;
+ struct omap_nand_info *info = this->priv;
+ int cs = info->cs;
/*
* Point the IO_ADDR to DATA and ADDRESS registers instead
writeb(cmd, this->IO_ADDR_W);
}
-#ifdef CONFIG_SPL_BUILD
/* Check wait pin as dev ready indicator */
-int omap_spl_dev_ready(struct mtd_info *mtd)
+static int omap_dev_ready(struct mtd_info *mtd)
{
- return gpmc_cfg->status & (1 << 8);
+ register struct nand_chip *this = mtd->priv;
+ struct omap_nand_info *info = this->priv;
+ return gpmc_cfg->status & (1 << (8 + info->ws));
}
-#endif
-
/*
* gen_true_ecc - This function will generate true ECC value, which
/*
* omap_correct_data - Compares the ecc read from nand spare area with ECC
- * registers values and corrects one bit error if it has occured
+ * registers values and corrects one bit error if it has occurred
* Further details can be had from OMAP TRM and the following selected links:
* http://en.wikipedia.org/wiki/Hamming_code
* http://www.cs.utexas.edu/users/plaxton/c/337/05f/slides/ErrorCorrection-4.pdf
return 0;
}
-/*
- * Generic BCH interface
- */
-struct nand_bch_priv {
- struct bch_control *control;
- enum omap_ecc ecc_scheme;
-};
-
-/*
- * This can be a single instance cause all current users have only one NAND
- * with nearly the same setup (BCH8, some with ELM and others with sw BCH
- * library).
- * When some users with other BCH strength will exists this have to change!
- */
-static __maybe_unused struct nand_bch_priv bch_priv = {
- .control = NULL
-};
-
-/*
- * omap_reverse_list - re-orders list elements in reverse order [internal]
- * @list: pointer to start of list
- * @length: length of list
-*/
-void omap_reverse_list(u8 *list, unsigned int length)
-{
- unsigned int i, j;
- unsigned int half_length = length / 2;
- u8 tmp;
- for (i = 0, j = length - 1; i < half_length; i++, j--) {
- tmp = list[i];
- list[i] = list[j];
- list[j] = tmp;
- }
-}
-
/*
* omap_enable_hwecc - configures GPMC as per ECC scheme before read/write
* @mtd: MTD device structure
static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
{
struct nand_chip *nand = mtd->priv;
- struct nand_bch_priv *bch = nand->priv;
+ struct omap_nand_info *info = nand->priv;
unsigned int dev_width = (nand->options & NAND_BUSWIDTH_16) ? 1 : 0;
unsigned int ecc_algo = 0;
unsigned int bch_type = 0;
unsigned int eccsize1 = 0x00, eccsize0 = 0x00, bch_wrapmode = 0x00;
u32 ecc_size_config_val = 0;
u32 ecc_config_val = 0;
+ int cs = info->cs;
/* configure GPMC for specific ecc-scheme */
- switch (bch->ecc_scheme) {
+ switch (info->ecc_scheme) {
case OMAP_ECC_HAM1_CODE_SW:
return;
case OMAP_ECC_HAM1_CODE_HW:
eccsize1 = 2; /* non-ECC bits in nibbles per sector */
}
break;
+ case OMAP_ECC_BCH16_CODE_HW:
+ ecc_algo = 0x1;
+ bch_type = 0x2;
+ if (mode == NAND_ECC_WRITE) {
+ bch_wrapmode = 0x01;
+ eccsize0 = 0; /* extra bits in nibbles per sector */
+ eccsize1 = 52; /* OOB bits in nibbles per sector */
+ } else {
+ bch_wrapmode = 0x01;
+ eccsize0 = 52; /* ECC bits in nibbles per sector */
+ eccsize1 = 0; /* non-ECC bits in nibbles per sector */
+ }
+ break;
default:
return;
}
uint8_t *ecc_code)
{
struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *bch = chip->priv;
+ struct omap_nand_info *info = chip->priv;
uint32_t *ptr, val = 0;
int8_t i = 0, j;
- switch (bch->ecc_scheme) {
+ switch (info->ecc_scheme) {
case OMAP_ECC_HAM1_CODE_HW:
val = readl(&gpmc_cfg->ecc1_result);
ecc_code[0] = val & 0xFF;
ptr--;
}
break;
+ case OMAP_ECC_BCH16_CODE_HW:
+ val = readl(&gpmc_cfg->bch_result_4_6[0].bch_result_x[2]);
+ ecc_code[i++] = (val >> 8) & 0xFF;
+ ecc_code[i++] = (val >> 0) & 0xFF;
+ val = readl(&gpmc_cfg->bch_result_4_6[0].bch_result_x[1]);
+ ecc_code[i++] = (val >> 24) & 0xFF;
+ ecc_code[i++] = (val >> 16) & 0xFF;
+ ecc_code[i++] = (val >> 8) & 0xFF;
+ ecc_code[i++] = (val >> 0) & 0xFF;
+ val = readl(&gpmc_cfg->bch_result_4_6[0].bch_result_x[0]);
+ ecc_code[i++] = (val >> 24) & 0xFF;
+ ecc_code[i++] = (val >> 16) & 0xFF;
+ ecc_code[i++] = (val >> 8) & 0xFF;
+ ecc_code[i++] = (val >> 0) & 0xFF;
+ for (j = 3; j >= 0; j--) {
+ val = readl(&gpmc_cfg->bch_result_0_3[0].bch_result_x[j]
+ );
+ ecc_code[i++] = (val >> 24) & 0xFF;
+ ecc_code[i++] = (val >> 16) & 0xFF;
+ ecc_code[i++] = (val >> 8) & 0xFF;
+ ecc_code[i++] = (val >> 0) & 0xFF;
+ }
+ break;
default:
return -EINVAL;
}
/* ECC scheme specific syndrome customizations */
- switch (bch->ecc_scheme) {
+ switch (info->ecc_scheme) {
case OMAP_ECC_HAM1_CODE_HW:
break;
#ifdef CONFIG_BCH
case OMAP_ECC_BCH8_CODE_HW:
ecc_code[chip->ecc.bytes - 1] = 0x00;
break;
+ case OMAP_ECC_BCH16_CODE_HW:
+ break;
default:
return -EINVAL;
}
return 0;
}
+#ifdef CONFIG_NAND_OMAP_GPMC_PREFETCH
+
+#define PREFETCH_CONFIG1_CS_SHIFT 24
+#define PREFETCH_FIFOTHRESHOLD_MAX 0x40
+#define PREFETCH_FIFOTHRESHOLD(val) ((val) << 8)
+#define PREFETCH_STATUS_COUNT(val) (val & 0x00003fff)
+#define PREFETCH_STATUS_FIFO_CNT(val) ((val >> 24) & 0x7F)
+#define ENABLE_PREFETCH (1 << 7)
+
+/**
+ * omap_prefetch_enable - configures and starts prefetch transfer
+ * @fifo_th: fifo threshold to be used for read/ write
+ * @count: number of bytes to be transferred
+ * @is_write: prefetch read(0) or write post(1) mode
+ * @cs: chip select to use
+ */
+static int omap_prefetch_enable(int fifo_th, unsigned int count, int is_write, int cs)
+{
+ uint32_t val;
+
+ if (fifo_th > PREFETCH_FIFOTHRESHOLD_MAX)
+ return -EINVAL;
+
+ if (readl(&gpmc_cfg->prefetch_control))
+ return -EBUSY;
+
+ /* Set the amount of bytes to be prefetched */
+ writel(count, &gpmc_cfg->prefetch_config2);
+
+ val = (cs << PREFETCH_CONFIG1_CS_SHIFT) | (is_write & 1) |
+ PREFETCH_FIFOTHRESHOLD(fifo_th) | ENABLE_PREFETCH;
+ writel(val, &gpmc_cfg->prefetch_config1);
+
+ /* Start the prefetch engine */
+ writel(1, &gpmc_cfg->prefetch_control);
+
+ return 0;
+}
+
+/**
+ * omap_prefetch_reset - disables and stops the prefetch engine
+ */
+static void omap_prefetch_reset(void)
+{
+ writel(0, &gpmc_cfg->prefetch_control);
+ writel(0, &gpmc_cfg->prefetch_config1);
+}
+
+static int __read_prefetch_aligned(struct nand_chip *chip, uint32_t *buf, int len)
+{
+ int ret;
+ uint32_t cnt;
+ struct omap_nand_info *info = chip->priv;
+
+ ret = omap_prefetch_enable(PREFETCH_FIFOTHRESHOLD_MAX, len, 0, info->cs);
+ if (ret < 0)
+ return ret;
+
+ do {
+ int i;
+
+ cnt = readl(&gpmc_cfg->prefetch_status);
+ cnt = PREFETCH_STATUS_FIFO_CNT(cnt);
+
+ for (i = 0; i < cnt / 4; i++) {
+ *buf++ = readl(CONFIG_SYS_NAND_BASE);
+ len -= 4;
+ }
+ } while (len);
+
+ omap_prefetch_reset();
+
+ return 0;
+}
+
+static inline void omap_nand_read(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ if (chip->options & NAND_BUSWIDTH_16)
+ nand_read_buf16(mtd, buf, len);
+ else
+ nand_read_buf(mtd, buf, len);
+}
+
+static void omap_nand_read_prefetch(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ int ret;
+ uint32_t head, tail;
+ struct nand_chip *chip = mtd->priv;
+
+ /*
+ * If the destination buffer is unaligned, start with reading
+ * the overlap byte-wise.
+ */
+ head = ((uint32_t) buf) % 4;
+ if (head) {
+ omap_nand_read(mtd, buf, head);
+ buf += head;
+ len -= head;
+ }
+
+ /*
+ * Only transfer multiples of 4 bytes in a pre-fetched fashion.
+ * If there's a residue, care for it byte-wise afterwards.
+ */
+ tail = len % 4;
+
+ ret = __read_prefetch_aligned(chip, (uint32_t *)buf, len - tail);
+ if (ret < 0) {
+ /* fallback in case the prefetch engine is busy */
+ omap_nand_read(mtd, buf, len);
+ } else if (tail) {
+ buf += len - tail;
+ omap_nand_read(mtd, buf, tail);
+ }
+}
+#endif /* CONFIG_NAND_OMAP_GPMC_PREFETCH */
+
#ifdef CONFIG_NAND_OMAP_ELM
+/*
+ * omap_reverse_list - re-orders list elements in reverse order [internal]
+ * @list: pointer to start of list
+ * @length: length of list
+*/
+static void omap_reverse_list(u8 *list, unsigned int length)
+{
+ unsigned int i, j;
+ unsigned int half_length = length / 2;
+ u8 tmp;
+ for (i = 0, j = length - 1; i < half_length; i++, j--) {
+ tmp = list[i];
+ list[i] = list[j];
+ list[j] = tmp;
+ }
+}
+
/*
* omap_correct_data_bch - Compares the ecc read from nand spare area
- * with ECC registers values and corrects one bit error if it has occured
+ * with ECC registers values and corrects one bit error if it has occurred
*
* @mtd: MTD device structure
* @dat: page data
uint8_t *read_ecc, uint8_t *calc_ecc)
{
struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *bch = chip->priv;
- uint32_t eccbytes = chip->ecc.bytes;
+ struct omap_nand_info *info = chip->priv;
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
uint32_t error_count = 0, error_max;
- uint32_t error_loc[8];
+ uint32_t error_loc[ELM_MAX_ERROR_COUNT];
enum bch_level bch_type;
uint32_t i, ecc_flag = 0;
- uint8_t count, err = 0;
+ uint8_t count;
uint32_t byte_pos, bit_pos;
+ int err = 0;
/* check calculated ecc */
- for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) {
+ for (i = 0; i < ecc->bytes && !ecc_flag; i++) {
if (calc_ecc[i] != 0x00)
ecc_flag = 1;
}
/* check for whether its a erased-page */
ecc_flag = 0;
- for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) {
+ for (i = 0; i < ecc->bytes && !ecc_flag; i++) {
if (read_ecc[i] != 0xff)
ecc_flag = 1;
}
* while reading ECC result we read it in big endian.
* Hence while loading to ELM we have rotate to get the right endian.
*/
- switch (bch->ecc_scheme) {
+ switch (info->ecc_scheme) {
case OMAP_ECC_BCH8_CODE_HW:
bch_type = BCH_8_BIT;
- omap_reverse_list(calc_ecc, eccbytes - 1);
+ omap_reverse_list(calc_ecc, ecc->bytes - 1);
+ break;
+ case OMAP_ECC_BCH16_CODE_HW:
+ bch_type = BCH_16_BIT;
+ omap_reverse_list(calc_ecc, ecc->bytes);
break;
default:
return -EINVAL;
}
/* use elm module to check for errors */
elm_config(bch_type);
- if (elm_check_error(calc_ecc, bch_type, &error_count, error_loc)) {
- printf("nand: error: uncorrectable ECC errors\n");
- return -EINVAL;
- }
+ err = elm_check_error(calc_ecc, bch_type, &error_count, error_loc);
+ if (err)
+ return err;
+
/* correct bch error */
for (count = 0; count < error_count; count++) {
- switch (bch->ecc_scheme) {
+ switch (info->ecc_scheme) {
case OMAP_ECC_BCH8_CODE_HW:
/* 14th byte in ECC is reserved to match ROM layout */
- error_max = SECTOR_BYTES + (eccbytes - 1);
+ error_max = SECTOR_BYTES + (ecc->bytes - 1);
+ break;
+ case OMAP_ECC_BCH16_CODE_HW:
+ error_max = SECTOR_BYTES + ecc->bytes;
break;
default:
return -EINVAL;
bit_pos = error_loc[count] % 8;
if (byte_pos < SECTOR_BYTES) {
dat[byte_pos] ^= 1 << bit_pos;
- printf("nand: bit-flip corrected @data=%d\n", byte_pos);
+ debug("nand: bit-flip corrected @data=%d\n", byte_pos);
} else if (byte_pos < error_max) {
read_ecc[byte_pos - SECTOR_BYTES] ^= 1 << bit_pos;
- printf("nand: bit-flip corrected @oob=%d\n", byte_pos -
+ debug("nand: bit-flip corrected @oob=%d\n", byte_pos -
SECTOR_BYTES);
} else {
err = -EBADMSG;
oob += eccbytes) {
chip->ecc.hwctl(mtd, NAND_ECC_READ);
/* read data */
- chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_pos, page);
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_pos, -1);
chip->read_buf(mtd, p, eccsize);
/* read respective ecc from oob area */
- chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, page);
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, -1);
chip->read_buf(mtd, oob, eccbytes);
/* read syndrome */
chip->ecc.calculate(mtd, p, &ecc_calc[i]);
/* cannot correct more than 8 errors */
unsigned int errloc[8];
struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *chip_priv = chip->priv;
- struct bch_control *bch = chip_priv->control;
+ struct omap_nand_info *info = chip->priv;
- count = decode_bch(bch, NULL, 512, read_ecc, calc_ecc, NULL, errloc);
+ count = decode_bch(info->control, NULL, 512, read_ecc, calc_ecc,
+ NULL, errloc);
if (count > 0) {
/* correct errors */
for (i = 0; i < count; i++) {
/* correct data only, not ecc bytes */
if (errloc[i] < 8*512)
data[errloc[i]/8] ^= 1 << (errloc[i] & 7);
- printf("corrected bitflip %u\n", errloc[i]);
+ debug("corrected bitflip %u\n", errloc[i]);
#ifdef DEBUG
puts("read_ecc: ");
/*
static void __maybe_unused omap_free_bch(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *chip_priv = chip->priv;
- struct bch_control *bch = NULL;
-
- if (chip_priv)
- bch = chip_priv->control;
+ struct omap_nand_info *info = chip->priv;
- if (bch) {
- free_bch(bch);
- chip_priv->control = NULL;
+ if (info->control) {
+ free_bch(info->control);
+ info->control = NULL;
}
}
#endif /* CONFIG_BCH */
*/
static int omap_select_ecc_scheme(struct nand_chip *nand,
enum omap_ecc ecc_scheme, unsigned int pagesize, unsigned int oobsize) {
- struct nand_bch_priv *bch = nand->priv;
+ struct omap_nand_info *info = nand->priv;
struct nand_ecclayout *ecclayout = &omap_ecclayout;
int eccsteps = pagesize / SECTOR_BYTES;
int i;
debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n");
/* For this ecc-scheme, ecc.bytes, ecc.layout, ... are
* initialized in nand_scan_tail(), so just set ecc.mode */
- bch_priv.control = NULL;
+ info->control = NULL;
nand->ecc.mode = NAND_ECC_SOFT;
nand->ecc.layout = NULL;
nand->ecc.size = 0;
- bch->ecc_scheme = OMAP_ECC_HAM1_CODE_SW;
break;
case OMAP_ECC_HAM1_CODE_HW:
(3 * eccsteps) + BADBLOCK_MARKER_LENGTH));
return -EINVAL;
}
- bch_priv.control = NULL;
+ info->control = NULL;
/* populate ecc specific fields */
memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
nand->ecc.mode = NAND_ECC_HW;
ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
BADBLOCK_MARKER_LENGTH;
- bch->ecc_scheme = OMAP_ECC_HAM1_CODE_HW;
break;
case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
return -EINVAL;
}
/* check if BCH S/W library can be used for error detection */
- bch_priv.control = init_bch(13, 8, 0x201b);
- if (!bch_priv.control) {
+ info->control = init_bch(13, 8, 0x201b);
+ if (!info->control) {
printf("nand: error: could not init_bch()\n");
return -ENODEV;
}
ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
BADBLOCK_MARKER_LENGTH;
- bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW;
break;
#else
printf("nand: error: CONFIG_BCH required for ECC\n");
}
/* intialize ELM for ECC error detection */
elm_init();
+ info->control = NULL;
/* populate ecc specific fields */
memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
nand->ecc.mode = NAND_ECC_HW;
ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
BADBLOCK_MARKER_LENGTH;
- bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW;
break;
#else
printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n");
return -EINVAL;
#endif
+ case OMAP_ECC_BCH16_CODE_HW:
+#ifdef CONFIG_NAND_OMAP_ELM
+ debug("nand: using OMAP_ECC_BCH16_CODE_HW\n");
+ /* check ecc-scheme requirements before updating ecc info */
+ if ((26 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
+ printf("nand: error: insufficient OOB: require=%d\n", (
+ (26 * eccsteps) + BADBLOCK_MARKER_LENGTH));
+ return -EINVAL;
+ }
+ /* intialize ELM for ECC error detection */
+ elm_init();
+ /* populate ecc specific fields */
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.size = SECTOR_BYTES;
+ nand->ecc.bytes = 26;
+ nand->ecc.strength = 16;
+ nand->ecc.hwctl = omap_enable_hwecc;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc;
+ nand->ecc.read_page = omap_read_page_bch;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
+ for (i = 0; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - nand->ecc.bytes -
+ BADBLOCK_MARKER_LENGTH;
+ break;
+#else
+ printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n");
+ return -EINVAL;
+#endif
default:
debug("nand: error: ecc scheme not enabled or supported\n");
return -EINVAL;
if (ecc_scheme != OMAP_ECC_HAM1_CODE_SW)
nand->ecc.layout = ecclayout;
+ info->ecc_scheme = ecc_scheme;
return 0;
}
return -EINVAL;
}
} else {
- err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW,
+ if (eccstrength == 1) {
+ err = omap_select_ecc_scheme(nand,
+ OMAP_ECC_HAM1_CODE_SW,
mtd->writesize, mtd->oobsize);
+ } else if (eccstrength == 8) {
+ err = omap_select_ecc_scheme(nand,
+ OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
+ mtd->writesize, mtd->oobsize);
+ } else {
+ printf("nand: error: unsupported ECC scheme\n");
+ return -EINVAL;
+ }
}
/* Update NAND handling after ECC mode switch */
int board_nand_init(struct nand_chip *nand)
{
int32_t gpmc_config = 0;
- cs = 0;
+ int cs = cs_next++;
int err = 0;
/*
* xloader/Uboot's gpmc configuration would have configured GPMC for
nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
- nand->priv = &bch_priv;
+ omap_nand_info[cs].control = NULL;
+ omap_nand_info[cs].cs = cs;
+ omap_nand_info[cs].ws = wscfg[cs];
+ nand->priv = &omap_nand_info[cs];
nand->cmd_ctrl = omap_nand_hwcontrol;
nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
- /* If we are 16 bit dev, our gpmc config tells us that */
- if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000)
- nand->options |= NAND_BUSWIDTH_16;
-
nand->chip_delay = 100;
nand->ecc.layout = &omap_ecclayout;
+ /* configure driver and controller based on NAND device bus-width */
+ gpmc_config = readl(&gpmc_cfg->cs[cs].config1);
+#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
+ nand->options |= NAND_BUSWIDTH_16;
+ writel(gpmc_config | (0x1 << 12), &gpmc_cfg->cs[cs].config1);
+#else
+ nand->options &= ~NAND_BUSWIDTH_16;
+ writel(gpmc_config & ~(0x1 << 12), &gpmc_cfg->cs[cs].config1);
+#endif
/* select ECC scheme */
#if defined(CONFIG_NAND_OMAP_ECCSCHEME)
err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME,
if (err)
return err;
-#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_NAND_OMAP_GPMC_PREFETCH
+ nand->read_buf = omap_nand_read_prefetch;
+#else
if (nand->options & NAND_BUSWIDTH_16)
nand->read_buf = nand_read_buf16;
else
nand->read_buf = nand_read_buf;
- nand->dev_ready = omap_spl_dev_ready;
#endif
+ nand->dev_ready = omap_dev_ready;
+
return 0;
}