This is currently implemented in net/eth.c
Look in include/net.h for details.
+config PHYLIB
+ bool "Ethernet PHY (physical media interface) support"
+ help
+ Enable Ethernet PHY (physical media interface) support.
+
+config RTL8211X_PHY_FORCE_MASTER
+ bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
+ depends on PHYLIB
+ help
+ Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
+ This can work around link stability and data corruption issues on gigabit
+ links which can occur in slave mode on certain PHYs, e.g. on the
+ RTL8211C(L).
+
+ Please note that two directly connected devices (i.e. via crossover cable)
+ will not be able to establish a link between each other if they both force
+ master mode. Multiple devices forcing master mode when connected by a
+ network switch do not pose a problem as the switch configures its affected
+ ports into slave mode.
+
+ This option only affects gigabit links. If you must establish a direct
+ connection between two devices which both force master mode, try forcing
+ the link speed to 100MBit/s.
+
+ If unsure, say N.
+
menuconfig NETDEVICES
bool "Network device support"
depends on NET
if NETDEVICES
+config AG7XXX
+ bool "Atheros AG7xxx Ethernet MAC support"
+ depends on DM_ETH && ARCH_ATH79
+ select PHYLIB
+ help
+ This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
+ present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
+
+
+config ALTERA_TSE
+ bool "Altera Triple-Speed Ethernet MAC support"
+ depends on DM_ETH
+ select PHYLIB
+ help
+ This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
+ Please find details on the "Triple-Speed Ethernet MegaCore Function
+ Resource Center" of Altera.
+
+config DWC_ETH_QOS
+ bool "Synopsys DWC Ethernet QOS device support"
+ depends on DM_ETH
+ select PHYLIB
+ help
+ This driver supports the Synopsys Designware Ethernet QOS (Quality
+ Of Service) IP block. The IP supports many options for bus type,
+ clocking/reset structure, and feature list. This driver currently
+ supports the specific configuration used in NVIDIA's Tegra186 chip,
+ but should be extensible to other combinations quite easily.
+
+config E1000
+ bool "Intel PRO/1000 Gigabit Ethernet support"
+ help
+ This driver supports Intel(R) PRO/1000 gigabit ethernet family of
+ adapters. For more information on how to identify your adapter, go
+ to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+config E1000_SPI_GENERIC
+ bool "Allow access to the Intel 8257x SPI bus"
+ depends on E1000
+ help
+ Allow generic access to the SPI bus on the Intel 8257x, for
+ example with the "sspi" command.
+
+config E1000_SPI
+ bool "Enable SPI bus utility code"
+ depends on E1000
+ help
+ Utility code for direct access to the SPI bus on Intel 8257x.
+ This does not do anything useful unless you set at least one
+ of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
+
+config CMD_E1000
+ bool "Enable the e1000 command"
+ depends on E1000
+ help
+ This enables the 'e1000' management command for E1000 devices. When
+ used on devices with SPI support you can reprogram the EEPROM from
+ U-Boot.
+
config ETH_SANDBOX
depends on DM_ETH && SANDBOX
default y
config ETH_DESIGNWARE
bool "Synopsys Designware Ethernet MAC"
+ select PHYLIB
help
This MAC is present in SoCs from various vendors. It supports
100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
provide the PHY (physical media interface).
+config ETHOC
+ bool "OpenCores 10/100 Mbps Ethernet MAC"
+ help
+ This MAC is present in OpenRISC and Xtensa XTFPGA boards.
+
+config FEC_MXC
+ bool "FEC Ethernet controller"
+ depends on MX5 || MX6
+ help
+ This driver supports the 10/100 Fast Ethernet controller for
+ NXP i.MX processors.
+
+config MVPP2
+ bool "Marvell Armada 375 network interface support"
+ depends on ARMADA_375
+ select PHYLIB
+ help
+ This driver supports the network interface units in the
+ Marvell ARMADA 375 SoC.
+
+config PCH_GBE
+ bool "Intel Platform Controller Hub EG20T GMAC driver"
+ depends on DM_ETH && DM_PCI
+ select PHYLIB
+ help
+ This MAC is present in Intel Platform Controller Hub EG20T. It
+ supports 10/100/1000 Mbps operation.
+
+config RTL8139
+ bool "Realtek 8139 series Ethernet controller driver"
+ help
+ This driver supports Realtek 8139 series fast ethernet family of
+ PCI chipsets/adapters.
+
+config RTL8169
+ bool "Realtek 8169 series Ethernet controller driver"
+ help
+ This driver supports Realtek 8169 series gigabit ethernet family of
+ PCI/PCIe chipsets/adapters.
+
+config SUN8I_EMAC
+ bool "Allwinner Sun8i Ethernet MAC support"
+ depends on DM_ETH
+ select PHYLIB
+ help
+ This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
+ It can be found in H3/A64/A83T based SoCs and compatible with both
+ External and Internal PHY's.
+
+config XILINX_AXIEMAC
+ depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
+ select PHYLIB
+ select MII
+ bool "Xilinx AXI Ethernet"
+ help
+ This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
+
+config XILINX_EMACLITE
+ depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
+ select PHYLIB
+ select MII
+ bool "Xilinx Ethernetlite"
+ help
+ This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
+
+config ZYNQ_GEM
+ depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
+ select PHYLIB
+ bool "Xilinx Ethernet GEM"
+ help
+ This MAC is present in Xilinx Zynq and ZynqMP SoCs.
+
+config PIC32_ETH
+ bool "Microchip PIC32 Ethernet Support"
+ depends on DM_ETH && MACH_PIC32
+ select PHYLIB
+ help
+ This driver implements 10/100 Mbps Ethernet and MAC layer for
+ Microchip PIC32 microcontrollers.
+
endif # NETDEVICES
projects / u-boot / blobdiff