+source "drivers/net/phy/Kconfig"
+
config DM_ETH
bool "Enable Driver Model for Ethernet drivers"
depends on DM
This is currently implemented in net/eth.c
Look in include/net.h for details.
-config PHYLIB
- bool "Ethernet PHY (physical media interface) support"
- help
- Enable Ethernet PHY (physical media interface) support.
-
-config RTL8211X_PHY_FORCE_MASTER
- bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
- depends on PHYLIB
- help
- Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
- This can work around link stability and data corruption issues on gigabit
- links which can occur in slave mode on certain PHYs, e.g. on the
- RTL8211C(L).
-
- Please note that two directly connected devices (i.e. via crossover cable)
- will not be able to establish a link between each other if they both force
- master mode. Multiple devices forcing master mode when connected by a
- network switch do not pose a problem as the switch configures its affected
- ports into slave mode.
-
- This option only affects gigabit links. If you must establish a direct
- connection between two devices which both force master mode, try forcing
- the link speed to 100MBit/s.
-
- If unsure, say N.
-
menuconfig NETDEVICES
bool "Network device support"
depends on NET
Please find details on the "Triple-Speed Ethernet MegaCore Function
Resource Center" of Altera.
+config DWC_ETH_QOS
+ bool "Synopsys DWC Ethernet QOS device support"
+ depends on DM_ETH
+ select PHYLIB
+ help
+ This driver supports the Synopsys Designware Ethernet QOS (Quality
+ Of Service) IP block. The IP supports many options for bus type,
+ clocking/reset structure, and feature list. This driver currently
+ supports the specific configuration used in NVIDIA's Tegra186 chip,
+ but should be extensible to other combinations quite easily.
+
config E1000
bool "Intel PRO/1000 Gigabit Ethernet support"
help
help
This MAC is present in OpenRISC and Xtensa XTFPGA boards.
+config FEC_MXC
+ bool "FEC Ethernet controller"
+ depends on MX5 || MX6
+ help
+ This driver supports the 10/100 Fast Ethernet controller for
+ NXP i.MX processors.
+
+config FTMAC100
+ bool "Ftmac100 Ethernet Support"
+ help
+ This MAC is present in Andestech SoCs.
+
config MVPP2
- bool "Marvell Armada 375 network interface support"
- depends on ARMADA_375
+ bool "Marvell Armada 375/7K/8K network interface support"
+ depends on ARMADA_375 || ARMADA_8K
select PHYLIB
help
This driver supports the network interface units in the
- Marvell ARMADA 375 SoC.
+ Marvell ARMADA 375, 7K and 8K SoCs.
+
+config MACB
+ bool "Cadence MACB/GEM Ethernet Interface"
+ depends on DM_ETH
+ select PHYLIB
+ help
+ The Cadence MACB ethernet interface is found on many Atmel
+ AT91 and SAMA5 parts. This driver also supports the Cadence
+ GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
+ Say Y to include support for the MACB/GEM chip.
config PCH_GBE
bool "Intel Platform Controller Hub EG20T GMAC driver"
This MAC is present in Intel Platform Controller Hub EG20T. It
supports 10/100/1000 Mbps operation.
+config RGMII
+ bool "Enable RGMII"
+ help
+ Enable the support of the Reduced Gigabit Media-Independent
+ Interface (RGMII).
+
config RTL8139
bool "Realtek 8139 series Ethernet controller driver"
help
This driver supports Realtek 8169 series gigabit ethernet family of
PCI/PCIe chipsets/adapters.
+config SUN7I_GMAC
+ bool "Enable Allwinner GMAC Ethernet support"
+ help
+ Enable the support for Sun7i GMAC Ethernet controller
+
+config SUN4I_EMAC
+ bool "Allwinner Sun4i Ethernet MAC support"
+ depends on DM_ETH
+ help
+ This driver supports the Allwinner based SUN4I Ethernet MAC.
+
config SUN8I_EMAC
bool "Allwinner Sun8i Ethernet MAC support"
depends on DM_ETH
help
This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
It can be found in H3/A64/A83T based SoCs and compatible with both
- External and Internal PHY's.
+ External and Internal PHYs.
config XILINX_AXIEMAC
depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
config XILINX_EMACLITE
- depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
+ depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
select PHYLIB
select MII
bool "Xilinx Ethernetlite"
This driver implements 10/100 Mbps Ethernet and MAC layer for
Microchip PIC32 microcontrollers.
+config GMAC_ROCKCHIP
+ bool "Rockchip Synopsys Designware Ethernet MAC"
+ depends on DM_ETH && ETH_DESIGNWARE
+ help
+ This driver provides Rockchip SoCs network support based on the
+ Synopsys Designware driver.
+
+config RENESAS_RAVB
+ bool "Renesas Ethernet AVB MAC"
+ depends on DM_ETH && RCAR_GEN3
+ select PHYLIB
+ help
+ This driver implements support for the Ethernet AVB block in
+ Renesas M3 and H3 SoCs.
+
endif # NETDEVICES