source "drivers/net/phy/Kconfig"
+source "drivers/net/pfe_eth/Kconfig"
config DM_ETH
bool "Enable Driver Model for Ethernet drivers"
This is currently implemented in net/eth.c
Look in include/net.h for details.
+config DRIVER_TI_CPSW
+ bool "TI Common Platform Ethernet Switch"
+ select PHYLIB
+ help
+ This driver supports the TI three port switch gigabit ethernet
+ subsystem found in the TI SoCs.
+
menuconfig NETDEVICES
bool "Network device support"
depends on NET
help
This MAC is present in OpenRISC and Xtensa XTFPGA boards.
+config FEC_MXC_SHARE_MDIO
+ bool "Share the MDIO bus for FEC controller"
+ depends on FEC_MXC
+
+config FEC_MXC_MDIO_BASE
+ hex "MDIO base address for the FEC controller"
+ depends on FEC_MXC_SHARE_MDIO
+ help
+ This specifies the MDIO registers base address. It is used when
+ two FEC controllers share MDIO bus.
+
config FEC_MXC
bool "FEC Ethernet controller"
- depends on MX5 || MX6
+ depends on MX5 || MX6 || MX7
help
This driver supports the 10/100 Fast Ethernet controller for
NXP i.MX processors.
help
This MAC is present in Andestech SoCs.
+config MVGBE
+ bool "Marvell Orion5x/Kirkwood network interface support"
+ depends on KIRKWOOD || ORION5X
+ help
+ This driver supports the network interface units in the
+ Marvell Orion5x and Kirkwood SoCs
+
config MVNETA
- bool "Marvell Armada 385 network interface support"
- depends on ARMADA_XP || ARMADA_38X
+ bool "Marvell Armada XP/385/3700 network interface support"
+ depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
select PHYLIB
help
This driver supports the network interface units in the
- Marvell ARMADA XP and 38X SoCs
+ Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
config MVPP2
bool "Marvell Armada 375/7K/8K network interface support"
GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
Say Y to include support for the MACB/GEM chip.
+config MACB_ZYNQ
+ bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
+ depends on MACB
+ help
+ The Cadence MACB ethernet interface was used on Zynq platform.
+ Say Y to enable support for the MACB/GEM in Zynq chip.
+
config PCH_GBE
bool "Intel Platform Controller Hub EG20T GMAC driver"
depends on DM_ETH && DM_PCI
This driver supports Realtek 8169 series gigabit ethernet family of
PCI/PCIe chipsets/adapters.
+config SMC911X
+ bool "SMSC LAN911x and LAN921x controller driver"
+
+if SMC911X
+
+config SMC911X_BASE
+ hex "SMC911X Base Address"
+ help
+ Define this to hold the physical address
+ of the device (I/O space)
+
+choice
+ prompt "SMC911X bus width"
+ default SMC911X_16_BIT
+
+config SMC911X_32_BIT
+ bool "Enable 32-bit interface"
+
+config SMC911X_16_BIT
+ bool "Enable 16-bit interface"
+ help
+ Define this if data bus is 16 bits. If your processor
+ automatically converts one 32 bit word to two 16 bit
+ words you may also try CONFIG_SMC911X_32_BIT.
+
+endchoice
+endif #SMC911X
+
config SUN7I_GMAC
bool "Enable Allwinner GMAC Ethernet support"
help
Enable the support for Sun7i GMAC Ethernet controller
+config SUN7I_GMAC_FORCE_TXERR
+ bool "Force PA17 as gmac function"
+ depends on SUN7I_GMAC
+ help
+ Some ethernet phys needs TXERR control. Since the GMAC
+ doesn't have such signal, setting PA17 as GMAC function
+ makes the pin output low, which enables data transmission.
+
config SUN4I_EMAC
bool "Allwinner Sun4i Ethernet MAC support"
depends on DM_ETH
+ select PHYLIB
help
This driver supports the Allwinner based SUN4I Ethernet MAC.
It can be found in H3/A64/A83T based SoCs and compatible with both
External and Internal PHYs.
+config SH_ETHER
+ bool "Renesas SH Ethernet MAC"
+ select PHYLIB
+ help
+ This driver supports the Ethernet for Renesas SH and ARM SoCs.
+
config XILINX_AXIEMAC
depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
select PHYLIB
config MPC8XX_FEC
bool "Fast Ethernet Controller on MPC8XX"
- depends on 8xx
+ depends on MPC8xx
select MII
help
This driver implements support for the Fast Ethernet Controller
on MPC8XX
+config SNI_AVE
+ bool "Socionext AVE Ethernet support"
+ depends on DM_ETH && ARCH_UNIPHIER
+ select PHYLIB
+ select SYSCON
+ select REGMAP
+ help
+ This driver implements support for the Socionext AVE Ethernet
+ controller, as found on the Socionext UniPhier family.
+
config ETHER_ON_FEC1
bool "FEC1"
depends on MPC8XX_FEC
The PHY does not have a RXERR line (RMII only).
(so program the FEC to ignore it).
+config SYS_DPAA_QBMAN
+ bool "Device tree fixup for QBMan on freescale SOCs"
+ depends on (ARM || PPC) && !SPL_BUILD
+ default y if ARCH_B4860 || \
+ ARCH_B4420 || \
+ ARCH_P1023 || \
+ ARCH_P2041 || \
+ ARCH_T1023 || \
+ ARCH_T1024 || \
+ ARCH_T1040 || \
+ ARCH_T1042 || \
+ ARCH_T2080 || \
+ ARCH_T2081 || \
+ ARCH_T4240 || \
+ ARCH_T4160 || \
+ ARCH_P4080 || \
+ ARCH_P3041 || \
+ ARCH_P5040 || \
+ ARCH_P5020 || \
+ ARCH_LS1043A || \
+ ARCH_LS1046A
+ help
+ QBman fixups to allow deep sleep in DPAA 1 SOCs
+
+config TSEC_ENET
+ select PHYLIB
+ bool "Enable Three-Speed Ethernet Controller"
+ help
+ This driver implements support for the (Enhanced) Three-Speed
+ Ethernet Controller found on Freescale SoCs.
+
endif # NETDEVICES
projects / u-boot / blobdiff