#include <asm/arch/imx-regs.h>
#include <asm/io.h>
#include <asm/errno.h>
+#include <linux/compiler.h>
DECLARE_GLOBAL_DATA_PTR;
+/*
+ * Timeout the transfer after 5 mS. This is usually a bit more, since
+ * the code in the tightloops this timeout is used in adds some overhead.
+ */
+#define FEC_XFER_TIMEOUT 5000
+
#ifndef CONFIG_MII
#error "CONFIG_MII has to be defined!"
#endif
return val;
}
-static void fec_mii_setspeed(struct fec_priv *fec)
+static void fec_mii_setspeed(struct ethernet_regs *eth)
{
/*
* Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
* and do not drop the Preamble.
*/
writel((((imx_get_fecclk() / 1000000) + 2) / 5) << 1,
- &fec->eth->mii_speed);
- debug("%s: mii_speed %08x\n", __func__, readl(&fec->eth->mii_speed));
+ ð->mii_speed);
+ debug("%s: mii_speed %08x\n", __func__, readl(ð->mii_speed));
}
static int fec_mdio_write(struct ethernet_regs *eth, uint8_t phyAddr,
#ifndef CONFIG_PHYLIB
static int miiphy_restart_aneg(struct eth_device *dev)
{
+ int ret = 0;
+#if !defined(CONFIG_FEC_MXC_NO_ANEG)
struct fec_priv *fec = (struct fec_priv *)dev->priv;
struct ethernet_regs *eth = fec->bus->priv;
- int ret = 0;
/*
* Wake up from sleep if necessary
if (fec->mii_postcall)
ret = fec->mii_postcall(fec->phy_id);
+#endif
return ret;
}
static int fec_rx_task_enable(struct fec_priv *fec)
{
- writel(1 << 24, &fec->eth->r_des_active);
+ writel(FEC_R_DES_ACTIVE_RDAR, &fec->eth->r_des_active);
return 0;
}
static int fec_tx_task_enable(struct fec_priv *fec)
{
- writel(1 << 24, &fec->eth->x_des_active);
+ writel(FEC_X_DES_ACTIVE_TDAR, &fec->eth->x_des_active);
return 0;
}
return 0;
}
-static void fec_eth_phy_config(struct eth_device *dev)
+/*
+ * Do initial configuration of the FEC registers
+ */
+static void fec_reg_setup(struct fec_priv *fec)
{
-#ifdef CONFIG_PHYLIB
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
- struct phy_device *phydev;
+ uint32_t rcntrl;
- phydev = phy_connect(fec->bus, fec->phy_id, dev,
- PHY_INTERFACE_MODE_RGMII);
- if (phydev) {
- fec->phydev = phydev;
- phy_config(phydev);
- }
-#endif
+ /*
+ * Set interrupt mask register
+ */
+ writel(0x00000000, &fec->eth->imask);
+
+ /*
+ * Clear FEC-Lite interrupt event register(IEVENT)
+ */
+ writel(0xffffffff, &fec->eth->ievent);
+
+
+ /*
+ * Set FEC-Lite receive control register(R_CNTRL):
+ */
+
+ /* Start with frame length = 1518, common for all modes. */
+ rcntrl = PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT;
+ if (fec->xcv_type != SEVENWIRE) /* xMII modes */
+ rcntrl |= FEC_RCNTRL_FCE | FEC_RCNTRL_MII_MODE;
+ if (fec->xcv_type == RGMII)
+ rcntrl |= FEC_RCNTRL_RGMII;
+ else if (fec->xcv_type == RMII)
+ rcntrl |= FEC_RCNTRL_RMII;
+
+ writel(rcntrl, &fec->eth->r_cntrl);
}
/**
#endif
#ifdef CONFIG_PHYLIB
- if (!fec->phydev)
- fec_eth_phy_config(edev);
- if (fec->phydev) {
+ {
/* Start up the PHY */
- phy_startup(fec->phydev);
+ int ret = phy_startup(fec->phydev);
+
+ if (ret) {
+ printf("Could not initialize PHY %s\n",
+ fec->phydev->dev->name);
+ return ret;
+ }
speed = fec->phydev->speed;
- } else {
- speed = _100BASET;
}
#else
miiphy_wait_aneg(edev);
{
struct fec_priv *fec = (struct fec_priv *)dev->priv;
uint32_t mib_ptr = (uint32_t)&fec->eth->rmon_t_drop;
- uint32_t rcntrl;
uint32_t size;
int i, ret;
(unsigned)fec->rbd_base + size);
}
- /*
- * Set interrupt mask register
- */
- writel(0x00000000, &fec->eth->imask);
-
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
- writel(0xffffffff, &fec->eth->ievent);
-
-
- /*
- * Set FEC-Lite receive control register(R_CNTRL):
- */
-
- /* Start with frame length = 1518, common for all modes. */
- rcntrl = PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT;
- if (fec->xcv_type == SEVENWIRE)
- rcntrl |= FEC_RCNTRL_FCE;
- else if (fec->xcv_type == RGMII)
- rcntrl |= FEC_RCNTRL_RGMII;
- else if (fec->xcv_type == RMII)
- rcntrl |= FEC_RCNTRL_RMII;
- else /* MII mode */
- rcntrl |= FEC_RCNTRL_FCE | FEC_RCNTRL_MII_MODE;
-
- writel(rcntrl, &fec->eth->r_cntrl);
+ fec_reg_setup(fec);
- if (fec->xcv_type == MII10 || fec->xcv_type == MII100)
- fec_mii_setspeed(fec);
+ if (fec->xcv_type != SEVENWIRE)
+ fec_mii_setspeed(fec->bus->priv);
/*
* Set Opcode/Pause Duration Register
* @param[in] length Data count in bytes
* @return 0 on success
*/
-static int fec_send(struct eth_device *dev, volatile void *packet, int length)
+static int fec_send(struct eth_device *dev, void *packet, int length)
{
unsigned int status;
- uint32_t size;
+ uint32_t size, end;
uint32_t addr;
+ int timeout = FEC_XFER_TIMEOUT;
+ int ret = 0;
/*
* This routine transmits one frame. This routine only accepts
#endif
addr = (uint32_t)packet;
- size = roundup(length, ARCH_DMA_MINALIGN);
- flush_dcache_range(addr, addr + size);
+ end = roundup(addr + length, ARCH_DMA_MINALIGN);
+ addr &= ~(ARCH_DMA_MINALIGN - 1);
+ flush_dcache_range(addr, end);
writew(length, &fec->tbd_base[fec->tbd_index].data_length);
writel(addr, &fec->tbd_base[fec->tbd_index].data_pointer);
* invalidate data cache to see what's really in RAM. Also, we need
* barrier here.
*/
- invalidate_dcache_range(addr, addr + size);
- while (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY) {
- udelay(1);
- invalidate_dcache_range(addr, addr + size);
+ while (--timeout) {
+ if (!(readl(&fec->eth->x_des_active) & FEC_X_DES_ACTIVE_TDAR))
+ break;
}
- debug("fec_send: status 0x%x index %d\n",
+ if (!timeout)
+ ret = -EINVAL;
+
+ invalidate_dcache_range(addr, addr + size);
+ if (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY)
+ ret = -EINVAL;
+
+ debug("fec_send: status 0x%x index %d ret %i\n",
readw(&fec->tbd_base[fec->tbd_index].status),
- fec->tbd_index);
+ fec->tbd_index, ret);
/* for next transmission use the other buffer */
if (fec->tbd_index)
fec->tbd_index = 0;
else
fec->tbd_index = 1;
- return 0;
+ return ret;
}
/**
int frame_length, len = 0;
struct nbuf *frame;
uint16_t bd_status;
- uint32_t addr, size;
+ uint32_t addr, size, end;
int i;
- uchar buff[FEC_MAX_PKT_SIZE];
+ uchar buff[FEC_MAX_PKT_SIZE] __aligned(ARCH_DMA_MINALIGN);
/*
* Check if any critical events have happened
* Invalidate data cache over the buffer
*/
addr = (uint32_t)frame;
- size = roundup(frame_length, ARCH_DMA_MINALIGN);
- invalidate_dcache_range(addr, addr + size);
+ end = roundup(addr + frame_length, ARCH_DMA_MINALIGN);
+ addr &= ~(ARCH_DMA_MINALIGN - 1);
+ invalidate_dcache_range(addr, end);
/*
* Fill the buffer and pass it to upper layers
return len;
}
-static int fec_probe(bd_t *bd, int dev_id, int phy_id, uint32_t base_addr)
+static void fec_set_dev_name(char *dest, int dev_id)
+{
+ sprintf(dest, (dev_id == -1) ? "FEC" : "FEC%i", dev_id);
+}
+
+#ifdef CONFIG_PHYLIB
+int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr,
+ struct mii_dev *bus, struct phy_device *phydev)
+#else
+static int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr,
+ struct mii_dev *bus, int phy_id)
+#endif
{
struct eth_device *edev;
struct fec_priv *fec;
- struct mii_dev *bus;
unsigned char ethaddr[6];
uint32_t start;
int ret = 0;
udelay(10);
}
- /*
- * Set interrupt mask register
- */
- writel(0x00000000, &fec->eth->imask);
-
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
- writel(0xffffffff, &fec->eth->ievent);
-
- /*
- * Set FEC-Lite receive control register(R_CNTRL):
- */
- /*
- * Frame length=1518; MII mode;
- */
- writel((PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT) | FEC_RCNTRL_FCE |
- FEC_RCNTRL_MII_MODE, &fec->eth->r_cntrl);
- fec_mii_setspeed(fec);
-
- if (dev_id == -1) {
- sprintf(edev->name, "FEC");
- fec->dev_id = 0;
- } else {
- sprintf(edev->name, "FEC%i", dev_id);
- fec->dev_id = dev_id;
- }
- fec->phy_id = phy_id;
-
- bus = mdio_alloc();
- if (!bus) {
- printf("mdio_alloc failed\n");
- ret = -ENOMEM;
- goto err3;
- }
- bus->read = fec_phy_read;
- bus->write = fec_phy_write;
- sprintf(bus->name, edev->name);
-#ifdef CONFIG_MX28
- /*
- * The i.MX28 has two ethernet interfaces, but they are not equal.
- * Only the first one can access the MDIO bus.
- */
- bus->priv = (struct ethernet_regs *)MXS_ENET0_BASE;
+ fec_reg_setup(fec);
+ fec_set_dev_name(edev->name, dev_id);
+ fec->dev_id = (dev_id == -1) ? 0 : dev_id;
+ fec->bus = bus;
+ fec_mii_setspeed(bus->priv);
+#ifdef CONFIG_PHYLIB
+ fec->phydev = phydev;
+ phy_connect_dev(phydev, edev);
+ /* Configure phy */
+ phy_config(phydev);
#else
- bus->priv = fec->eth;
+ fec->phy_id = phy_id;
#endif
- ret = mdio_register(bus);
- if (ret) {
- printf("mdio_register failed\n");
- free(bus);
- ret = -ENOMEM;
- goto err3;
- }
- fec->bus = bus;
eth_register(edev);
if (fec_get_hwaddr(edev, dev_id, ethaddr) == 0) {
debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr);
memcpy(edev->enetaddr, ethaddr, 6);
}
- /* Configure phy */
- fec_eth_phy_config(edev);
return ret;
-
err3:
free(fec);
err2:
return ret;
}
-#ifndef CONFIG_FEC_MXC_MULTI
-int fecmxc_initialize(bd_t *bd)
+struct mii_dev *fec_get_miibus(uint32_t base_addr, int dev_id)
{
- int lout = 1;
+ struct ethernet_regs *eth = (struct ethernet_regs *)base_addr;
+ struct mii_dev *bus;
+ int ret;
- debug("eth_init: fec_probe(bd)\n");
- lout = fec_probe(bd, -1, CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+ bus = mdio_alloc();
+ if (!bus) {
+ printf("mdio_alloc failed\n");
+ return NULL;
+ }
+ bus->read = fec_phy_read;
+ bus->write = fec_phy_write;
+ bus->priv = eth;
+ fec_set_dev_name(bus->name, dev_id);
- return lout;
+ ret = mdio_register(bus);
+ if (ret) {
+ printf("mdio_register failed\n");
+ free(bus);
+ return NULL;
+ }
+ fec_mii_setspeed(eth);
+ return bus;
}
-#endif
int fecmxc_initialize_multi(bd_t *bd, int dev_id, int phy_id, uint32_t addr)
{
- int lout = 1;
+ uint32_t base_mii;
+ struct mii_dev *bus = NULL;
+#ifdef CONFIG_PHYLIB
+ struct phy_device *phydev = NULL;
+#endif
+ int ret;
+#ifdef CONFIG_MX28
+ /*
+ * The i.MX28 has two ethernet interfaces, but they are not equal.
+ * Only the first one can access the MDIO bus.
+ */
+ base_mii = MXS_ENET0_BASE;
+#else
+ base_mii = addr;
+#endif
debug("eth_init: fec_probe(bd, %i, %i) @ %08x\n", dev_id, phy_id, addr);
- lout = fec_probe(bd, dev_id, phy_id, addr);
+ bus = fec_get_miibus(base_mii, dev_id);
+ if (!bus)
+ return -ENOMEM;
+#ifdef CONFIG_PHYLIB
+ phydev = phy_find_by_mask(bus, 1 << phy_id, PHY_INTERFACE_MODE_RGMII);
+ if (!phydev) {
+ free(bus);
+ return -ENOMEM;
+ }
+ ret = fec_probe(bd, dev_id, addr, bus, phydev);
+#else
+ ret = fec_probe(bd, dev_id, addr, bus, phy_id);
+#endif
+ if (ret) {
+#ifdef CONFIG_PHYLIB
+ free(phydev);
+#endif
+ free(bus);
+ }
+ return ret;
+}
- return lout;
+#ifdef CONFIG_FEC_MXC_PHYADDR
+int fecmxc_initialize(bd_t *bd)
+{
+ return fecmxc_initialize_multi(bd, -1, CONFIG_FEC_MXC_PHYADDR,
+ IMX_FEC_BASE);
}
+#endif
#ifndef CONFIG_PHYLIB
int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int))
projects / u-boot / blobdiff