prompt "Select Sunxi PMIC Variant"
depends on ARCH_SUNXI
default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
- default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
+ default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
default AXP818_POWER if MACH_SUN8I_A83T
default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I
config AXP152_POWER
bool "axp152 pmic support"
depends on MACH_SUN5I
+ select AXP_PMIC_BUS
select CMD_POWEROFF
---help---
Select this to enable support for the axp152 pmic found on most
config AXP209_POWER
bool "axp209 pmic support"
depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+ select AXP_PMIC_BUS
select CMD_POWEROFF
---help---
Select this to enable support for the axp209 pmic found on most
config AXP221_POWER
bool "axp221 / axp223 pmic support"
- depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
+ depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
+ select AXP_PMIC_BUS
select CMD_POWEROFF
---help---
Select this to enable support for the axp221/axp223 pmic found on most
config AXP809_POWER
bool "axp809 pmic support"
depends on MACH_SUN9I
+ select AXP_PMIC_BUS
select CMD_POWEROFF
---help---
Say y here to enable support for the axp809 pmic found on A80 boards.
config AXP818_POWER
bool "axp818 pmic support"
depends on MACH_SUN8I_A83T
+ select AXP_PMIC_BUS
select CMD_POWEROFF
---help---
Say y here to enable support for the axp818 pmic found on
config AXP_DCDC1_VOLT
int "axp pmic dcdc1 voltage"
depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
- default 3300 if AXP818_POWER
+ default 3300 if AXP818_POWER || MACH_SUN8I_R40
default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
---help---
Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
On A80 boards dcdc2 powers the GPU and can be left off.
On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
+ On R40 boards dcdc2 is VDD-CPU and should be 1.1V
config AXP_DCDC3_VOLT
int "axp pmic dcdc3 voltage"
default 900 if AXP809_POWER || AXP818_POWER
default 1500 if AXP152_POWER
default 1250 if AXP209_POWER
+ default 1100 if MACH_SUN8I_R40
default 1200 if MACH_SUN6I || MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
+ On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
config AXP_DCDC4_VOLT
int "axp pmic dcdc4 voltage"
---help---
Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
disable dcdc5.
- On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
+ On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
should be 1.5V, 1.35V if DDR3L is used.
config AXP_ALDO1_VOLT
int "axp pmic (a)ldo1 voltage"
depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
- default 0 if MACH_SUN6I
+ default 0 if MACH_SUN6I || MACH_SUN8I_R40
default 1800 if MACH_SUN8I_A83T
default 3000 if MACH_SUN8I || MACH_SUN9I
---help---
Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
disable aldo3.
On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
- On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
+ On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
+ be 3.0V.
On A80 boards aldo3 is normally not used.
On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
3.0V.
is typically used to power the VDD-CPU and should be 1200mV.
Values can range from 680mV till 1950mV.
+config TWL4030_POWER
+ depends on OMAP34XX
+ bool "Enable driver for TI TWL4030 power management chip"
+ imply CMD_POWEROFF
+ ---help---
+ The TWL4030 in a combination audio CODEC/power management with
+ GPIO and it is commonly used with the OMAP3 family of processors
+
endmenu