i2c, mxc: rework i2c base address names for different SoCs

[u-boot] / drivers / power / Kconfig

diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index af668871291ce924e69cf8529247ecc21bdc0a03..23cdd714ae6aac75424c0151cba43902362e69b8 100644 (file)
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -1,3 +1,9 @@
+menu "Power"
+
+source "drivers/power/pmic/Kconfig"
+
+source "drivers/power/regulator/Kconfig"
+
 config AXP221_POWER
        boolean "axp221 / axp223 pmic support"
        depends on MACH_SUN6I || MACH_SUN8I
@@ -6,12 +12,22 @@ config AXP221_POWER
        Say y here to enable support for the axp221 / axp223 pmic found on most
        sun6i (A31) / sun8i (A23) boards.
 
+config AXP221_DCDC1_VOLT
+       int "axp221 dcdc1 voltage"
+       depends on AXP221_POWER
+       default 3000
+       ---help---
+       Set the voltage (mV) to program the axp221 dcdc1 at, set to 0 to
+       disable dcdc1. This is typically used as generic 3.3V IO voltage for
+       things like GPIO-s, sdcard interfaces, etc. On most boards this is
+       undervolted to 3.0V to safe battery.
+
 config AXP221_DLDO1_VOLT
        int "axp221 dldo1 voltage"
        depends on AXP221_POWER
-       default -1
+       default 0
        ---help---
-       Set the voltage (mV) to program the axp221 dldo1 at, set to -1 to
+       Set the voltage (mV) to program the axp221 dldo1 at, set to 0 to
        disable dldo1. On sun6i (A31) boards with ethernet this is often used
        to power the ethernet phy. On sun8i (A23) boards this is often used to
        power the wifi.
@@ -19,37 +35,49 @@ config AXP221_DLDO1_VOLT
 config AXP221_DLDO4_VOLT
        int "axp221 dldo4 voltage"
        depends on AXP221_POWER
-       default -1
+       default 0
        ---help---
-       Set the voltage (mV) to program the axp221 dldo4 at, set to -1 to
+       Set the voltage (mV) to program the axp221 dldo4 at, set to 0 to
        disable dldo4.
 
 config AXP221_ALDO1_VOLT
        int "axp221 aldo1 voltage"
        depends on AXP221_POWER
-       default -1
+       default 0
        ---help---
-       Set the voltage (mV) to program the axp221 aldo1 at, set to -1 to
+       Set the voltage (mV) to program the axp221 aldo1 at, set to 0 to
        disable aldo1. On sun6i (A31) boards which have a wifi module this is
        often used to power the wifi module.
 
 config AXP221_ALDO2_VOLT
        int "axp221 aldo2 voltage"
        depends on AXP221_POWER
-       default 1800 if MACH_SUN6I
+       default 0 if MACH_SUN6I
        default 2500 if MACH_SUN8I
        ---help---
-       Set the voltage (mV) to program the axp221 aldo2 at, set to -1 to
-       disable aldo2. On sun6i (A31) boards this is typically connected to
-       VCC-PM, which powers the port M gpios, and should be set to 1.8V.
-       On sun8i (A23) this is typically connected to VDD-DLL and must be
-       set to 2.5V.
+       Set the voltage (mV) to program the axp221 aldo2 at, set to 0 to
+       disable aldo2. On sun6i (A31) boards this is typically unused and
+       should be disabled, if it is used for LPDDR2 it should be set to 1.8V.
+       On sun8i (A23) this is typically connected to VDD-DLL and must be set
+       to 2.5V.
 
 config AXP221_ALDO3_VOLT
        int "axp221 aldo3 voltage"
        depends on AXP221_POWER
        default 3000
        ---help---
-       Set the voltage (mV) to program the axp221 aldo3 at, set to -1 to
+       Set the voltage (mV) to program the axp221 aldo3 at, set to 0 to
        disable aldo3. This is typically connected to VCC-PLL and AVCC and
        must be set to 3V.
+
+config AXP221_ELDO3_VOLT
+       int "axp221 eldo3 voltage"
+       depends on AXP221_POWER
+       default 0
+       ---help---
+       Set the voltage (mV) to program the axp221 eldo3 at, set to 0 to
+       disable eldo3. On some A31(s) tablets it might be used to supply
+       1.2V for the SSD2828 chip (converter of parallel LCD interface
+       into MIPI DSI).
+
+endmenu