depends on ARCH_SUNXI
default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
+ default AXP818_POWER if MACH_SUN8I_A83T
default SUNXI_NO_PMIC if MACH_SUN8I_H3
config SUNXI_NO_PMIC
config AXP152_POWER
boolean "axp152 pmic support"
depends on MACH_SUN5I
+ select CMD_POWEROFF
---help---
Select this to enable support for the axp152 pmic found on most
A10s boards.
config AXP209_POWER
boolean "axp209 pmic support"
depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+ select CMD_POWEROFF
---help---
Select this to enable support for the axp209 pmic found on most
A10, A13 and A20 boards.
config AXP221_POWER
boolean "axp221 / axp223 pmic support"
depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
+ select CMD_POWEROFF
---help---
Select this to enable support for the axp221/axp223 pmic found on most
A23 and A31 boards.
+config AXP818_POWER
+ boolean "axp818 pmic support"
+ depends on MACH_SUN8I_A83T
+ ---help---
+ Say y here to enable support for the axp818 pmic found on
+ A83T dev board.
+
+config SY8106A_POWER
+ boolean "SY8106A pmic support"
+ depends on MACH_SUN8I_H3
+ ---help---
+ Select this to enable support for the SY8106A pmic found on some
+ H3 boards.
+
endchoice
config AXP_DCDC1_VOLT
int "axp pmic dcdc1 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
+ default 3300 if AXP818_POWER
default 3000 if MACH_SUN6I || MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
generic 3.3V IO voltage for external devices like the lcd-panal and
sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
- safe battery. On A31 devices dcdc1 is also used for VCC-IO.
+ safe battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
+ dcdc1 is used for VCC-IO, nand, usb0, sd , etc.
config AXP_DCDC2_VOLT
int "axp pmic dcdc2 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
+ default 900 if AXP818_POWER
default 1400 if AXP152_POWER || AXP209_POWER
default 1200 if MACH_SUN6I
default 1100 if MACH_SUN8I
On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
+ On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
config AXP_DCDC3_VOLT
int "axp pmic dcdc3 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
+ default 900 if AXP818_POWER
default 1500 if AXP152_POWER
default 1250 if AXP209_POWER
default 1200 if MACH_SUN6I || MACH_SUN8I
should be 1.25V.
On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
+ On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
config AXP_DCDC4_VOLT
int "axp pmic dcdc4 voltage"
- depends on AXP152_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP221_POWER || AXP818_POWER
default 1250 if AXP152_POWER
default 1200 if MACH_SUN6I
default 0 if MACH_SUN8I
On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
On A23 / A33 boards dcdc4 is unused and should be disabled.
+ On A83T boards dcdc4 is used for VDD-GPU.
config AXP_DCDC5_VOLT
int "axp pmic dcdc5 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 1500 if MACH_SUN6I || MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
disable dcdc5.
- On A23 / A31 / A33 boards dcdc5 is VCC-DRAM and should be 1.5V.
+ On A23 / A31 / A33 / A83T boards dcdc5 is VCC-DRAM and should be 1.5V,
+ 1.35V if DDR3L is used.
config AXP_ALDO1_VOLT
int "axp pmic (a)ldo1 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0 if MACH_SUN6I
+ default 1800 if MACH_SUN8I_A83T
default 3000 if MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
disable aldo1.
On A31 boards aldo1 is often used to power the wifi module.
On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
+ On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
+ should be 1.8V.
config AXP_ALDO2_VOLT
int "axp pmic (a)ldo2 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
default 3000 if AXP152_POWER || AXP209_POWER
default 0 if MACH_SUN6I
+ default 1800 if MACH_SUN8I_A83T
default 2500 if MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
On A31 boards aldo2 is typically unused and should be disabled.
On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
+ On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
+ LPDDR2, and the codec. It should be 1.8V.
config AXP_ALDO3_VOLT
int "axp pmic (a)ldo3 voltage"
- depends on AXP209_POWER || AXP221_POWER
+ depends on AXP209_POWER || AXP221_POWER || AXP818_POWER
default 0 if AXP209_POWER
default 3000 if MACH_SUN6I || MACH_SUN8I
---help---
disable aldo3.
On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
+ On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
+ 3.0V.
config AXP_ALDO4_VOLT
int "axp pmic (a)ldo4 voltage"
config AXP_DLDO1_VOLT
int "axp pmic dldo1 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
config AXP_DLDO2_VOLT
int "axp pmic dldo2 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
config AXP_DLDO3_VOLT
int "axp pmic dldo3 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
config AXP_DLDO4_VOLT
int "axp pmic dldo4 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
config AXP_ELDO1_VOLT
int "axp pmic eldo1 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
config AXP_ELDO2_VOLT
int "axp pmic eldo2 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
config AXP_ELDO3_VOLT
int "axp pmic eldo3 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
1.2V for the SSD2828 chip (converter of parallel LCD interface
into MIPI DSI).
+config AXP_FLDO1_VOLT
+ int "axp pmic fldo1 voltage"
+ depends on AXP818_POWER
+ default 0 if MACH_SUN8I_A83T
+ ---help---
+ Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
+ disable fldo1.
+ On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
+ used.
+
+config AXP_FLDO2_VOLT
+ int "axp pmic eldo2 voltage"
+ depends on AXP818_POWER
+ default 900 if MACH_SUN8I_A83T
+ ---help---
+ Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
+ disable fldo2.
+ On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
+
+config AXP_FLDO3_VOLT
+ int "axp pmic fldo3 voltage"
+ depends on AXP818_POWER
+ default 0
+ ---help---
+ Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
+ disable fldo3.
+
+config SY8106A_VOUT1_VOLT
+ int "SY8106A pmic VOUT1 voltage"
+ depends on SY8106A_POWER
+ default 1200
+ ---help---
+ Set the voltage (mV) to program the SY8106A pmic VOUT1. This
+ is typically used to power the VDD-CPU and should be 1200mV.
+ Values can range from 680mV till 1950mV.
+
endmenu
projects / u-boot / blobdiff