+#
+# Serial device configuration
+#
+
+menu "Serial drivers"
+
+config REQUIRE_SERIAL_CONSOLE
+ bool "Require a serial port for console"
+ # Running without a serial console is not supported by the
+ # non-dm serial code
+ depends on DM_SERIAL
+ default y
+ help
+ Require a serial port for the console, and panic if none is found
+ during serial port initialization (default y). Set this to n on
+ boards which have no debug serial port whatsoever.
+
config DM_SERIAL
bool "Enable Driver Model for serial drivers"
depends on DM
serial drivers are up and running (done in serial_init()). Otherwise
the drivers may conflict and you will get strange output.
+choice
+ prompt "Select which UART will provide the debug UART"
+ depends on DEBUG_UART
+
+config DEBUG_UART_NS16550
+ bool "ns16550"
+ help
+ Select this to enable a debug UART using the ns16550 driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver model serial is running.
+
+config DEBUG_EFI_CONSOLE
+ bool "EFI"
+ depends on EFI_APP
+ help
+ Select this to enable a debug console which calls back to EFI to
+ output to the console. This can be useful for early debugging of
+ U-Boot when running on top of EFI (Extensive Firmware Interface).
+ This is a type of BIOS used by PCs.
+
+config DEBUG_UART_S5P
+ bool "Samsung S5P"
+ help
+ Select this to enable a debug UART using the serial_s5p driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver-model serial is running.
+
+endchoice
+
config DEBUG_UART_BASE
hex "Base address of UART"
depends on DEBUG_UART
A default should be provided by your board, but if not you will need
to use the correct value here.
+config DEBUG_UART_SHIFT
+ int "UART register shift"
+ depends on DEBUG_UART
+ default 0 if DEBUG_UART
+ help
+ Some UARTs (notably ns16550) support different register layouts
+ where the registers are spaced either as bytes, words or some other
+ value. Use this value to specify the shift to use, where 0=byte
+ registers, 2=32-bit word registers, etc.
+
+config ROCKCHIP_SERIAL
+ bool "Rockchip on-chip UART support"
+ depends on ARCH_ROCKCHIP && DM_SERIAL
+ help
+ Select this to enable a debug UART for Rockchip devices. This uses
+ the ns16550 driver. You will need to #define CONFIG_SYS_NS16550 in
+ your board config header. The clock input is automatically set to
+ use the oscillator (24MHz).
+
+config SANDBOX_SERIAL
+ bool "Sandbox UART support"
+ depends on SANDBOX
+ help
+ Select this to enable a seral UART for sandbox. This is required to
+ operate correctly, otherwise you will see no serial output from
+ sandbox. The emulated UART will display to the console and console
+ input will be fed into the UART. This allows you to interact with
+ U-Boot.
+
+ The operation of the console is controlled by the -t command-line
+ flag. In raw mode, U-Boot sees all characters from the terminal
+ before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
+ is processed by the terminal, and terminates U-Boot. Valid options
+ are:
+
+ -t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
+ -t raw Raw mode, Ctrl-C is processed by U-Boot
+ -t cooked Cooked mode, Ctrl-C terminates
+
config UNIPHIER_SERIAL
- bool "UniPhier on-chip UART support"
- depends on ARCH_UNIPHIER && DM_SERIAL
+ bool "Support for UniPhier on-chip UART"
+ depends on ARCH_UNIPHIER
help
- Support for the on-chip UARTs on the Panasonic UniPhier platform.
+ If you have a UniPhier based board and want to use the on-chip
+ serial ports, say Y to this option. If unsure, say N.
+
+config X86_SERIAL
+ bool "Support for 16550 serial port on x86 machines"
+ depends on X86
+ default y
+ help
+ Most x86 machines have a ns16550 UART or compatible. This can be
+ enabled in the device tree with the correct input clock frequency
+ provided (default 1843200). Enable this to obtain serial console
+ output.
+
+endmenu