*/
#include <common.h>
+#include <clk.h>
#include <dm.h>
#include <errno.h>
#include <fdtdec.h>
#define CONFIG_SYS_NS16550_IER 0x00
#endif /* CONFIG_SYS_NS16550_IER */
-#ifdef CONFIG_DM_SERIAL
-
-#ifndef CONFIG_SYS_NS16550_CLK
-#define CONFIG_SYS_NS16550_CLK 0
-#endif
-
static inline void serial_out_shift(void *addr, int shift, int value)
{
#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
#endif
}
+#ifdef CONFIG_DM_SERIAL
+
+#ifndef CONFIG_SYS_NS16550_CLK
+#define CONFIG_SYS_NS16550_CLK 0
+#endif
+
static void ns16550_writeb(NS16550_t port, int offset, int value)
{
struct ns16550_platdata *plat = port->plat;
unsigned char *addr;
offset *= 1 << plat->reg_shift;
- addr = map_physmem(plat->base, 0, MAP_NOCACHE) + offset;
+ addr = (unsigned char *)plat->base + offset;
+
/*
* As far as we know it doesn't make sense to support selection of
* these options at run-time, so use the existing CONFIG options.
*/
- serial_out_shift(addr, plat->reg_shift, value);
+ serial_out_shift(addr + plat->reg_offset, plat->reg_shift, value);
}
static int ns16550_readb(NS16550_t port, int offset)
unsigned char *addr;
offset *= 1 << plat->reg_shift;
- addr = map_physmem(plat->base, 0, MAP_NOCACHE) + offset;
+ addr = (unsigned char *)plat->base + offset;
- return serial_in_shift(addr, plat->reg_shift);
+ return serial_in_shift(addr + plat->reg_offset, plat->reg_shift);
}
/* We can clean these up once everything is moved to driver model */
(unsigned char *)addr - (unsigned char *)com_port)
#endif
-static inline int calc_divisor(NS16550_t port, int clock, int baudrate)
+int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate)
{
const unsigned int mode_x_div = 16;
return DIV_ROUND_CLOSEST(clock, mode_x_div * baudrate);
}
-int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate)
-{
-#ifdef CONFIG_OMAP1510
- /* If can't cleanly clock 115200 set div to 1 */
- if ((clock == 12000000) && (baudrate == 115200)) {
- port->osc_12m_sel = OSC_12M_SEL; /* enable 6.5 * divisor */
- return 1; /* return 1 for base divisor */
- }
- port->osc_12m_sel = 0; /* clear if previsouly set */
-#endif
-
- return calc_divisor(port, clock, baudrate);
-}
-
static void NS16550_setbrg(NS16550_t com_port, int baud_divisor)
{
serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr);
* feasible. The better fix is to move all users of this driver to
* driver model.
*/
- baud_divisor = calc_divisor(com_port, CONFIG_DEBUG_UART_CLOCK,
- CONFIG_BAUDRATE);
+ baud_divisor = ns16550_calc_divisor(com_port, CONFIG_DEBUG_UART_CLOCK,
+ CONFIG_BAUDRATE);
serial_dout(&com_port->ier, CONFIG_SYS_NS16550_IER);
serial_dout(&com_port->mcr, UART_MCRVAL);
serial_dout(&com_port->fcr, UART_FCRVAL);
return 0;
}
-#if CONFIG_IS_ENABLED(OF_CONTROL)
+#if CONFIG_IS_ENABLED(OF_CONTROL) && !CONFIG_IS_ENABLED(OF_PLATDATA)
int ns16550_serial_ofdata_to_platdata(struct udevice *dev)
{
struct ns16550_platdata *plat = dev->platdata;
fdt_addr_t addr;
+ struct clk clk;
+ int err;
/* try Processor Local Bus device first */
addr = dev_get_addr(dev);
if (addr == FDT_ADDR_T_NONE)
return -EINVAL;
+#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
plat->base = addr;
+#else
+ plat->base = (unsigned long)map_physmem(addr, 0, MAP_NOCACHE);
+#endif
+
+ plat->reg_offset = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+ "reg-offset", 0);
plat->reg_shift = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
"reg-shift", 0);
- plat->clock = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
- "clock-frequency",
- CONFIG_SYS_NS16550_CLK);
+
+ err = clk_get_by_index(dev, 0, &clk);
+ if (!err) {
+ err = clk_get_rate(&clk);
+ if (!IS_ERR_VALUE(err))
+ plat->clock = err;
+ } else if (err != -ENOENT && err != -ENODEV && err != -ENOSYS) {
+ debug("ns16550 failed to get clock\n");
+ return err;
+ }
+
+ if (!plat->clock)
+ plat->clock = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+ "clock-frequency",
+ CONFIG_SYS_NS16550_CLK);
if (!plat->clock) {
debug("ns16550 clock not defined\n");
return -EINVAL;
.setbrg = ns16550_serial_setbrg,
};
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
#if CONFIG_IS_ENABLED(OF_CONTROL)
/*
* Please consider existing compatible strings before adding a new
.flags = DM_FLAG_PRE_RELOC,
};
#endif
+#endif /* !OF_PLATDATA */
#endif /* CONFIG_DM_SERIAL */