mtd: nand: mxs_nand: use more precise function name

[u-boot] / drivers / usb / Kconfig

diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index e69de29bb2d1d6434b8b29ae775ad8c2e48c5391..4fbe172e05c87badc1555ff4fa52a79c913075d5 100644 (file)
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -0,0 +1,104 @@
+menuconfig USB
+       bool "USB support"
+       ---help---
+         Universal Serial Bus (USB) is a specification for a serial bus
+         subsystem which offers higher speeds and more features than the
+         traditional PC serial port.  The bus supplies power to peripherals
+         and allows for hot swapping.  Up to 127 USB peripherals can be
+         connected to a single USB host in a tree structure.
+
+         The USB host is the root of the tree, the peripherals are the
+         leaves and the inner nodes are special USB devices called hubs.
+         Most PCs now have USB host ports, used to connect peripherals
+         such as scanners, keyboards, mice, modems, cameras, disks,
+         flash memory, network links, and printers to the PC.
+
+         Say Y here if your device has an USB port, either host, peripheral or
+         dual-role.
+
+         For an USB host port, you then need to say Y to at least one of the
+         Host Controller Driver (HCD) options below.  Choose a USB 1.1
+         controller, such as "UHCI HCD support" or "OHCI HCD support",
+         and "EHCI HCD (USB 2.0) support" except for older systems that
+         do not have USB 2.0 support.  It doesn't normally hurt to select
+         them all if you are not certain.
+
+         If your system has a device-side USB port, used in the peripheral
+         side of the USB protocol, see the "USB Gadget" framework instead.
+
+         After choosing your HCD, then select drivers for the USB peripherals
+         you'll be using.  You may want to check out the information provided
+         in <file:Documentation/usb/> and especially the links given in
+         <file:Documentation/usb/usb-help.txt>.
+
+if USB
+
+config DM_USB
+       bool "Enable driver model for USB"
+       depends on USB && DM
+       help
+         Enable driver model for USB. The USB interface is then implemented
+         by the USB uclass. Multiple USB controllers of different types
+         (XHCI, EHCI) can be attached and used. The 'usb' command works as
+         normal. OCHI is not supported at present.
+
+         Much of the code is shared but with this option enabled the USB
+         uclass takes care of device enumeration. USB devices can be
+         declared with the U_BOOT_USB_DEVICE() macro and will be
+         automatically probed when found on the bus.
+
+source "drivers/usb/host/Kconfig"
+
+source "drivers/usb/dwc3/Kconfig"
+
+source "drivers/usb/musb/Kconfig"
+
+source "drivers/usb/musb-new/Kconfig"
+
+source "drivers/usb/emul/Kconfig"
+
+source "drivers/usb/phy/Kconfig"
+
+source "drivers/usb/ulpi/Kconfig"
+
+comment "USB peripherals"
+
+config USB_STORAGE
+       bool "USB Mass Storage support"
+       ---help---
+         Say Y here if you want to connect USB mass storage devices to your
+         board's USB port.
+
+config USB_KEYBOARD
+       bool "USB Keyboard support"
+       select SYS_STDIO_DEREGISTER
+       ---help---
+         Say Y here if you want to use a USB keyboard for U-Boot command line
+         input.
+
+if USB_KEYBOARD
+
+choice
+       prompt "USB keyboard polling"
+       default SYS_USB_EVENT_POLL
+       ---help---
+         Enable a polling mechanism for USB keyboard.
+
+       config SYS_USB_EVENT_POLL
+               bool "Interrupt polling"
+
+       config SYS_USB_EVENT_POLL_VIA_INT_QUEUE
+               bool "Poll via interrupt queue"
+
+       config SYS_USB_EVENT_POLL_VIA_CONTROL_EP
+               bool "Poll via control EP"
+
+endchoice
+
+endif
+
+source "drivers/usb/gadget/Kconfig"
+
+source "drivers/usb/eth/Kconfig"
+
+endif