#
comment "USB Host Controller Drivers"
+config USB_HOST
+ bool
+
config USB_XHCI_HCD
bool "xHCI HCD (USB 3.0) support"
+ select USB_HOST
---help---
The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
"SuperSpeed" host controller hardware.
-config USB_XHCI
- bool
- default USB_XHCI_HCD
- ---help---
- TODO: rename after most boards switch to Kconfig
-
if USB_XHCI_HCD
-config USB_XHCI_UNIPHIER
- bool "Support for UniPhier on-chip xHCI USB controller"
- depends on ARCH_UNIPHIER
- default y
- ---help---
- Enables support for the on-chip xHCI controller on UniPhier SoCs.
+config USB_XHCI_DWC3
+ bool "DesignWare USB3 DRD Core Support"
+ help
+ Say Y or if your system has a Dual Role SuperSpeed
+ USB controller based on the DesignWare USB3 IP Core.
-endif
+config USB_XHCI_MVEBU
+ bool "MVEBU USB 3.0 support"
+ default y
+ depends on ARCH_MVEBU
+ help
+ Choose this option to add support for USB 3.0 driver on mvebu
+ SoCs, which includes Armada8K, Armada3700 and other Armada
+ family SoCs.
+
+config USB_XHCI_ROCKCHIP
+ bool "Support for Rockchip on-chip xHCI USB controller"
+ depends on ARCH_ROCKCHIP
+ default y
+ help
+ Enables support for the on-chip xHCI controller on Rockchip SoCs.
-config USB_OHCI_GENERIC
- bool "Support for generic OHCI USB controller"
- depends on OF_CONTROL
- depends on DM_USB
- default n
- ---help---
- Enables support for generic OHCI controller.
+endif # USB_XHCI_HCD
config USB_EHCI_HCD
bool "EHCI HCD (USB 2.0) support"
+ select USB_HOST
---help---
The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
if USB_EHCI_HCD
+config USB_EHCI_ATMEL
+ bool "Support for Atmel on-chip EHCI USB controller"
+ depends on ARCH_AT91
+ default y
+ ---help---
+ Enables support for the on-chip EHCI controller on Atmel chips.
+
config USB_EHCI_MARVELL
bool "Support for MVEBU (AXP / A38x) on-chip EHCI USB controller"
depends on ARCH_MVEBU
---help---
Enables support for the on-chip EHCI controller on i.MX6 SoCs.
-config USB_EHCI_UNIPHIER
- bool "Support for UniPhier on-chip EHCI USB controller"
- depends on ARCH_UNIPHIER && OF_CONTROL
+config USB_EHCI_MX7
+ bool "Support for i.MX7 on-chip EHCI USB controller"
+ depends on ARCH_MX7
default y
---help---
- Enables support for the on-chip EHCI controller on UniPhier SoCs.
+ Enables support for the on-chip EHCI controller on i.MX7 SoCs.
+
+if USB_EHCI_MX7
+
+config MXC_USB_OTG_HACTIVE
+ bool "USB Power pin high active"
+ ---help---
+ Set the USB Power pin polarity to be high active (PWR_POL)
+
+endif
+
+config USB_EHCI_MSM
+ bool "Support for Qualcomm on-chip EHCI USB controller"
+ depends on DM_USB
+ select USB_ULPI_VIEWPORT
+ default n
+ ---help---
+ Enables support for the on-chip EHCI controller on Qualcomm
+ Snapdragon SoCs.
+ This driver supports combination of Chipidea USB controller
+ and Synapsys USB PHY in host mode only.
+
+config USB_EHCI_ZYNQ
+ bool "Support for Xilinx Zynq on-chip EHCI USB controller"
+ depends on ARCH_ZYNQ
+ default y
+ ---help---
+ Enable support for Zynq on-chip EHCI USB controller
config USB_EHCI_GENERIC
bool "Support for generic EHCI USB controller"
---help---
Enables support for generic EHCI controller.
-endif
+endif # USB_EHCI_HCD
+
+config USB_OHCI_HCD
+ bool "OHCI HCD (USB 1.1) support"
+ ---help---
+ The Open Host Controller Interface (OHCI) is a standard for accessing
+ USB 1.1 host controller hardware. It does more in hardware than Intel's
+ UHCI specification. If your USB host controller follows the OHCI spec,
+ say Y. On most non-x86 systems, and on x86 hardware that's not using a
+ USB controller from Intel or VIA, this is appropriate. If your host
+ controller doesn't use PCI, this is probably appropriate. For a PCI
+ based system where you're not sure, the "lspci -v" entry will list the
+ right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
+
+if USB_OHCI_HCD
+
+config USB_OHCI_GENERIC
+ bool "Support for generic OHCI USB controller"
+ depends on OF_CONTROL
+ depends on DM_USB
+ select USB_HOST
+ ---help---
+ Enables support for generic OHCI controller.
+
+endif # USB_OHCI_HCD
+
+config USB_UHCI_HCD
+ bool "UHCI HCD (most Intel and VIA) support"
+ select USB_HOST
+ ---help---
+ The Universal Host Controller Interface is a standard by Intel for
+ accessing the USB hardware in the PC (which is also called the USB
+ host controller). If your USB host controller conforms to this
+ standard, you may want to say Y, but see below. All recent boards
+ with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
+ i810, i820) conform to this standard. Also all VIA PCI chipsets
+ (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
+ 133) and LEON/GRLIB SoCs with the GRUSBHC controller.
+ If unsure, say Y.
+
+if USB_UHCI_HCD
+
+endif # USB_UHCI_HCD
projects / u-boot / blobdiff