/*****************************************************************************/
/* */
-/* _pia.h */
+/* _pia.h */
/* */
-/* Internal include file, do not use directly */
+/* Internal include file, do not use directly */
/* */
+/* The Peripheral Interface Adapter (PIA) chip (a 6520 or 6820) provides */
+/* parallel I/O interfacing; it was used in Atari 400/800 and Commodore PET */
+/* family of computers, for joystick and some interrupts. */
+/* Sources; various + Wikpedia article on "Peripheral Interface Adapter". */
/* */
/* */
/* (C) 2000 Freddy Offenga <taf_offenga@yahoo.com> */
+/* 2019-01-17: Bill Kendrick <nbs@sonic.net>: Defines for registers */
/* */
/* */
/* This software is provided 'as-is', without any expressed or implied */
#define __PIA_H
-/* Define a structure with the pia register offsets */
+/* Define a structure with the PIA register offsets */
struct __pia {
unsigned char porta; /* port A data r/w */
unsigned char portb; /* port B data r/w */
};
+/*****************************************************************************/
+/* PORTA and PORTB register bits */
+/*****************************************************************************/
-/* End of _pia.h */
-#endif
+/* See also: "JOY_xxx_MASK" in "atari.h" */
+
+/* Paddle 0-3 triggers (per PORTA bits) */
+#define PORTA_PTRIG3 0x80
+#define PORTA_PTRIG2 0x40
+#define PORTA_PTRIG1 0x08
+#define PORTA_PTRIG0 0x04
+
+
+/* On the Atari 400/800, PORTB is the same as PORTA, but for controller ports 3 & 4. */
+
+/* Paddle 4-7 triggers (per PORTB bits); only 400/800 had four controller ports */
+#define PORTB_PTRIG7 0x80
+#define PORTB_PTRIG6 0x40
+#define PORTB_PTRIG5 0x08
+#define PORTB_PTRIG4 0x04
+
+
+/* On the XL series of computers, PORTB has been changed to a memory and
+** LED control (1200XL model only) register (read/write):
+*/
+
+/* If set, the built-in OS is enabled, and occupies the address range $C000-$FFFF
+** (except that the area $D000-$D7FF will only access the hardware registers.)
+** If clear, RAM is enabled in this area (again, save for the hole.)
+*/
+#define PORTB_OSROM 0x01
+
+/* If set, RAM is enabled for the address range $A000-$BFFF.
+** If clear, the built-in BASIC ROM is enabled at this address.
+** And if there is a cartridge installed in the computer, it makes no difference.
+*/
+#define PORTB_BASICROM 0x02
+
+/* If set, the corresponding LED is turned off. If clear, the LED will be on.
+** (1200XL only)
+*/
+#define PORTB_LED1 0x04
+#define PORTB_LED2 0x08
+
+
+/* On the XE series of computers, PORTB is a bank-selected memory control register (read/write): */
+
+/* These bits determine which memory bank is visible to the CPU and/or ANTIC chip
+** when their Bank Switch bit is set. There are four possible banks of 16KB each.
+*/
+#define PORTB_BANKSELECT1 0x00
+#define PORTB_BANKSELECT2 0x04
+#define PORTB_BANKSELECT3 0x08
+#define PORTB_BANKSELECT4 0x0C
+/* If set, the CPU and/or ANTIC chip will access bank-switched memory mapped to the
+** address range $4000-$7FFF.
+** If clear, the CPU and/or ANTIC will see normal memory in this region.
+*/
+#define PORTB_BANKSWITCH_CPU 0x10
+#define PORTB_BANKSWITCH_ANTIC 0x20
+/* If set, RAM is enabled for the address range $5000-$57FF.
+** If clear, the self-test ROM (physically located at $D000-$D7FF, under the hardware registers)
+** is remapped to this memory area.
+*/
+#define PORTB_SELFTEST 0x80
+
+/*****************************************************************************/
+/* PACTL and PBCTL register bits */
+/*****************************************************************************/
+
+/* (W) Peripheral PA1/PB1 interrupt (IRQ) ("peripheral proceed line available") enable.
+** One equals enable. Set by the OS but available to the user; reset on powerup.
+** (PxCTL_IRQ_STATUS (R) bit will get set upon interrupt occurance)
+*/
+#define PxCTL_IRQ_ENABLE 0x01 /* bit 0 */
+
+/* Note: Bit 1 is always set to */
+
+/* (W) Controls PORTA/PORTB addressing
+** 1 = PORTA/PORTB register; read/write to controller port
+** 0 = direction control register; write to direction controls
+** (allows setting data flow; write 0s & 1s to PORTA/PORTB bits
+** to set which port's pins are read (input), or write (output),
+** respectively)
+*/
+#define PxCTL_ADDRESSING 0x04 /* bit 2 */
+
+/* (W) Peripheral motor control line; Turn the cassette on or off
+** (PACTL-specific register bit)
+** 0 = on
+** 1 = off
+*/
+#define PACTL_MOTOR_CONTROL 0x08 /* bit 3 */
+
+/* Peripheral command identification (serial bus command line)
+** (PBCTL-specific register bit)
+*/
+#define PBCTL_PERIPH_CMD_IDENT 0x08 /* bit 3 */
+
+/* Note: Bits 4 & 5 are always set to 1 */
+
+/* Note: Bit 6 is always set to 0 */
+
+/* (R) Peripheral interrupt (IRQ) status bit.
+** Set by Peripherals (PORTA / PORTB). Reset by reading from PORTA / PORTB.
+** PACTL's is interrupt status of PROCEED
+** PBCTL's is interrupt status of SIO
+*/
+#define PxCTL_IRQ_STATUS 0x80
+
+
+/* End of _pia.h */
+#endif
projects / cc65 / blobdiff