rename CFG_ENV macros to CONFIG_ENV

[u-boot] / include / configs / ASH405.h

diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 9e0ee371c2ce23864e15ab3d0ace114341ff24e7..228571419d0a26df9754cd8f1185b7dab765feae 100644 (file)
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -53,9 +53,13 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download  */
 #define CFG_LOADS_BAUD_CHANGE  1       /* allow baudrate change        */
 
+#define CONFIG_NET_MULTI       1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII             1       /* MII PHY management           */
 #define CONFIG_PHY_ADDR                0       /* PHY address                  */
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ    EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -144,40 +148,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
+#define CFG_NAND_BASE_LIST     { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE    1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US      25
 
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE    1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -251,9 +233,9 @@
 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
-#define CFG_ENV_IS_IN_EEPROM   1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET         0x100   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE           0x700   /* 2048 bytes may be used for env vars*/
+#define CONFIG_ENV_IS_IN_EEPROM        1       /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET              0x100   /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE                0x700   /* 2048 bytes may be used for env vars*/
                                   /* total size of a CAT24WC16 is 2048 bytes */
 
 #define CFG_NVRAM_BASE_ADDR    0xF0000500              /* NVRAM base address   */
@@ -276,16 +258,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE                16384   /* For AMCC 405 CPUs, older 405 ppc's   */
-                                       /* have only 8kB, 16kB is save here     */
-#define CFG_CACHELINE_SIZE     32      /* ...                  */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT    5       /* log base 2 of the above value        */
-#endif
-
 /*
  * Init Memory Controller:
  *