#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
- CONFIG_BOOTP_DNS | \
- CONFIG_BOOTP_DNS2 | \
- CONFIG_BOOTP_SEND_HOSTNAME )
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+
/*
* Command line configuration.
#define CONFIG_CMD_EEPROM
-#define CFG_NAND_LEGACY
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE }
+#define NAND_MAX_CHIPS 1
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US 25
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+#define CFG_NAND_QUIET 1
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_EEPROM_WREN 1
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/