Fix an overflow case in fdt_offset_ptr() detected by GCC 4.3.

[u-boot] / include / configs / HUB405.h

diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index 88cc6a4820ef1ee120fe14283df3d44967c3e643..0727606bbb87bc776dec10717363950537b1694e 100644 (file)
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -60,18 +60,30 @@
 
 #define CONFIG_PHY_CLK_FREQ    EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
-#define CONFIG_COMMANDS              ( CONFIG_CMD_DFL  | \
-                               CFG_CMD_DHCP    | \
-                               CFG_CMD_IRQ     | \
-                               CFG_CMD_ELF     | \
-                               CFG_CMD_NAND    | \
-                               CFG_CMD_I2C     | \
-                               CFG_CMD_MII     | \
-                               CFG_CMD_PING    | \
-                               CFG_CMD_EEPROM  )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled            */
 
@@ -88,7 +100,7 @@
 #define CFG_PROMPT_HUSH_PS2    "> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE     1024            /* Console I/O Buffer Size      */
 #else
 #define CFG_CBSIZE     256             /* Console I/O Buffer Size      */
@@ -145,7 +157,8 @@
 #define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
 #define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -219,9 +232,9 @@
 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
-#define CFG_ENV_IS_IN_EEPROM   1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET         0x100   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE           0x700   /* 2048 bytes may be used for env vars*/
+#define CONFIG_ENV_IS_IN_EEPROM        1       /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET              0x100   /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE                0x700   /* 2048 bytes may be used for env vars*/
                                   /* total size of a CAT24WC16 is 2048 bytes */
 
 #define CFG_NVRAM_BASE_ADDR    0xF0000500              /* NVRAM base address   */
@@ -244,16 +257,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE                16384   /* For AMCC 405 CPUs, older 405 ppc's   */
-                                       /* have only 8kB, 16kB is save here     */
-#define CFG_CACHELINE_SIZE     32      /* ...                  */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT    5       /* log base 2 of the above value        */
-#endif
-
 /*
  * Init Memory Controller:
  *