arm/km: disable ls (through jffs2 support)

[u-boot] / include / configs / MPC8323ERDB.h

diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index 7c843939c280fa44504bc30e3dfedd5ce2f2ac50..e25d5acc13641907f03ec372f678470ccfc68ee7 100644 (file)
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -17,6 +17,8 @@
 #define CONFIG_MPC83xx         1       /* MPC83xx family */
 #define CONFIG_MPC832x         1       /* MPC832x CPU specific */
 
+#define        CONFIG_SYS_TEXT_BASE    0xFE000000
+
 #define CONFIG_PCI             1
 
 /*
@@ -146,7 +148,7 @@
 /*
  * The reserved memory
  */
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
@@ -163,9 +165,8 @@
  */
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xE6000000      /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END        0x1000          /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE       0x100           /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000          /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
  * Local Bus Configuration & Clock Setup
@@ -262,7 +263,6 @@
  * Serial Port
  */
 #define CONFIG_CONS_INDEX      1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -338,7 +338,7 @@
  * QE UEC ethernet configuration
  */
 #define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME                "FSL UEC0"
+#define CONFIG_ETHPRIME                "UEC0"
 
 #define CONFIG_UEC_ETH1                /* ETH3 */
 
@@ -348,7 +348,7 @@
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK10
 #define CONFIG_SYS_UEC1_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       4
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE MII
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED        100
 #endif
 
@@ -360,7 +360,7 @@
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK3
 #define CONFIG_SYS_UEC2_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE MII
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED        100
 #endif
 
@@ -430,10 +430,10 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ           (8 << 20)       /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ           (256 << 20)     /* Initial Memory map for Linux */
 
 /*
  * Core HID Setup
@@ -508,14 +508,6 @@
 #define CONFIG_SYS_DBAT7L      CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U      CONFIG_SYS_IBAT7U
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01    /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02    /* Software reboot */
-
 #if (CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
@@ -552,11 +544,11 @@
        "netdev=" MK_STR(CONFIG_NETDEV) "\0"                            \
        "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                          \
        "tftpflash=tftp $loadaddr $uboot;"                              \
-               "protect off " MK_STR(TEXT_BASE) " +$filesize; "        \
-               "erase " MK_STR(TEXT_BASE) " +$filesize; "              \
-               "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "      \
-               "protect on " MK_STR(TEXT_BASE) " +$filesize; "         \
-               "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"     \
+               "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "     \
+               "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "           \
+               "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "   \
+               "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "              \
+               "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"  \
        "fdtaddr=780000\0"                                              \
        "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"                          \
        "ramdiskaddr=1000000\0"                                         \