#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
/*
* Only possible on E500 Version 2 or newer cores.
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
-#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */
+#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VSPEED2_TSEC3SER 0x1
#define PIXIS_VCFGEN1_TSEC1SER 0x20
#define PIXIS_VCFGEN1_TSEC3SER 0x40
+#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER)
+#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER)
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
+#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */
#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */
+#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */
#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */
-#define CONFIG_SYS_PCI1_MEM_BASE 0xc0000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000
#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
+#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */
-/* PCI view of System Memory */
-#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
-#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
-#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000
-
/* controller 2, Slot 1, tgtid 1, Base address 9000 */
-#define CONFIG_SYS_PCIE2_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 2,tgtid 2, Base address a000 */
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 3, direct to uli, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_MEM_BASE 0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS CONFIG_SYS_PCIE3_MEM_BASE
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */
-#define CONFIG_SYS_PCIE3_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */
-#define CONFIG_SYS_PCIE3_MEM_BASE2 0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_PHYS2 CONFIG_SYS_PCIE3_MEM_BASE2
+#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000
+#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000
+#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000
#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */
#if defined(CONFIG_PCI)
/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_PHYS
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT
/*PCI video card used*/
-/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_PHYS*/
+/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/
/* video */
#define CONFIG_VIDEO
#undef CONFIG_TULIP
#define CONFIG_RTL8139
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x) (x)
-#define _IO_BASE 0x00000000
-#endif
-
#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BASE
+ #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS
+ #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS
#define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
#endif
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_PIXIS_SGMII_CMD
#define CONFIG_FSL_SGMII_RISER 1
#define SGMII_RISER_PHY_OFFSET 0x1c
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
- #define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_NET
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions