#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE}
+#define CFG_FLASH_QUIET_TEST
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
/* define to use L1 as initial stack */
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
-
-#define OF_CPU "PowerPC,8544@0"
-#define OF_SOC "soc8544@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8544@e0000000/serial@4500"
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe1000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCI1_IO_SIZE 0x00010000 /* 64k */
/* PCI view of System Memory */
#define CFG_PCI_MEMORY_BUS 0x00000000
#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
#define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCIE2_IO_BASE 0x00000000
-#define CFG_PCIE2_IO_PHYS 0xe2000000
-#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCIE2_IO_PHYS 0xe1010000
+#define CFG_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 2,tgtid 2, Base address a000 */
#define CFG_PCIE1_MEM_BASE 0xa0000000
#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE 0x08000000 /* 128M */
-#define CFG_PCIE1_MEM_BASE2 0xa8000000
-#define CFG_PCIE1_MEM_PHYS2 CFG_PCIE1_MEM_BASE2
-#define CFG_PCIE1_MEM_SIZE2 0x04000000 /* 64M */
-#define CFG_PCIE1_IO_BASE 0x00000000 /* reuse mem LAW */
-#define CFG_PCIE1_IO_PHYS 0xaf000000
-#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCIE1_IO_BASE 0x00000000
+#define CFG_PCIE1_IO_PHYS 0xe1020000
+#define CFG_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 3, direct to uli, tgtid 3, Base address b000 */
#define CFG_PCIE3_MEM_BASE 0xb0000000
#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE
-#define CFG_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCIE3_MEM_SIZE 0x00100000 /* 1M */
#define CFG_PCIE3_IO_BASE 0x00000000
-#define CFG_PCIE3_IO_PHYS 0xe3000000
+#define CFG_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */
#define CFG_PCIE3_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCIE3_MEM_BASE2 0xb0200000
+#define CFG_PCIE3_MEM_PHYS2 CFG_PCIE3_MEM_BASE2
+#define CFG_PCIE3_MEM_SIZE2 0x00200000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
/*
* Internal Definitions
*
#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD
-#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD
-#define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD
#endif
#define CONFIG_IPADDR 192.168.1.251
#define CONFIG_BOOTFILE 8544ds/uImage.uboot
#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */
-#define CONFIG_SERVERIP 192.168.0.1
-#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.0.0
#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
#define CONFIG_BAUDRATE 115200
-#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
-#define PCIE_ENV \
- "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
- "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
- "pcieerr=md ${a}020 1; md ${a}e00 e;" \
- "pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
- "pci d.w $b.0 56 1;" \
- "pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
- "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;" \
- "pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \
- "pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
- "pci w $b.0 130 ffffffff\0" \
- "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
- "pcie1regs=setenv a e000a; run pciereg\0" \
- "pcie2regs=setenv a e0009; run pciereg\0" \
- "pcie3regs=setenv a e000b; run pciereg\0" \
- "pcie1cfg=setenv b 3; run pciecfg\0" \
- "pcie2cfg=setenv b 5; run pciecfg\0" \
- "pcie3cfg=setenv b 0; run pciecfg\0" \
- "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0" \
- "pcie2err=setenv a e0009; setenv b 5; run pcieerr\0" \
- "pcie3err=setenv a e000b; setenv b 0; run pcieerr\0" \
- "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0" \
- "pcie2errc=setenv a e0009; setenv b 5; run pcieerrc\0" \
- "pcie3errc=setenv a e000b; setenv b 0; run pcieerrc\0"
-#else
-#define PCIE_ENV ""
-#endif
-
-#if defined(CONFIG_PCI1)
-#define PCI_ENV \
- "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
- "echo e;md ${a}e00 9\0" \
- "pci1regs=setenv a e0008; run pcireg\0" \
- "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
- "pci d.w $b.0 56 1\0" \
- "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
- "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0" \
- "pci1err=setenv a e0008; setenv b 7; run pcierr\0" \
- "pci1errc=setenv a e0008; setenv b 7; run pcierrc\0"
-#else
-#define PCI_ENV ""
-#endif
-
-#if defined(CONFIG_TSEC_ENET)
-#define ENET_ENV \
- "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
- "md ${a}098 2\0" \
- "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
- "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
- "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
- "echo mib;md ${a}680 31\0" \
- "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
- "enet1regs=setenv a e0024; run enetreg\0" \
- "enet3regs=setenv a e0026; run enetreg\0"
-#else
-#define ENET_ENV ""
-#endif
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=8544ds/ramdisk.uboot\0" \
- "dtbaddr=c00000\0" \
- "dtbfile=8544ds/mpc8544ds.dtb\0" \
- "bdev=sda3\0" \
- "eoi=mw e00400b0 0\0" \
- "iack=md e00400a0 1\0" \
- "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
- "md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
- "ddrregs=setenv a e0002; run ddrreg\0" \
- "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
- "md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" \
- "guregs=setenv a e00e0; run gureg\0" \
- "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
- "ecmregs=setenv a e0001; run ecmreg\0" \
- "lawregs=md e0000c08 4b\0" \
- "lbcregs=md e0005000 36\0" \
- "dma0regs=md e0021100 12\0" \
- "dma1regs=md e0021180 12\0" \
- "dma2regs=md e0021200 12\0" \
- "dma3regs=md e0021280 12\0" \
- PCIE_ENV \
- PCI_ENV \
- ENET_ENV
-
+ "fdtaddr=c00000\0" \
+ "fdtfile=8544ds/mpc8544ds.dtb\0" \
+ "bdev=sda3\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr - $dtbaddr"
-
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr $ramdiskaddr $dtbaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr - $dtbaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#endif /* __CONFIG_H */
projects / u-boot / blobdiff