#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
/*
* When initializing flash, if we cannot find the manufacturer ID,
#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
#endif
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
/*
- * SDRAM on the Local Bus
+ * Local Bus Definitions
*/
-#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ * Port Size = 16 bits = BRx[19:20] = 10
+ * Use GPCM = BRx[24:26] = 000
+ * Valid = BRx[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
+ *
+ * OR0, OR1:
+ * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ * Reserved ORx[17:18] = 11, confusion here?
+ * CSNT = ORx[20] = 1
+ * ACS = half cycle delay = ORx[21:22] = 11
+ * SCY = 6 = ORx[24:27] = 0110
+ * TRLX = use relaxed timing = ORx[29] = 1
+ * EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
+ */
+
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */
-#define CFG_BR0_PRELIM 0xff801001 /* port size 16bit */
-#define CFG_BR1_PRELIM 0xff001001 /* port size 16bit */
+#define CFG_BR0_PRELIM 0xff801001
+#define CFG_BR1_PRELIM 0xff001001
-#define CFG_OR0_PRELIM 0xff806e61 /* 8MB Flash */
-#define CFG_OR1_PRELIM 0xff806e61 /* 8MB Flash */
+#define CFG_OR0_PRELIM 0xff806e65
+#define CFG_OR1_PRELIM 0xff806e65
#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
-#undef CONFIG_CLOCKS_IN_MHZ
/*
- * Local Bus Definitions
+ * SDRAM on the Local Bus
*/
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8555@0"
+#define OF_SOC "soc8555@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8555@e0000000/serial@4600"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe2100000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_MPC85XX_PCI2
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
+#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define FEC_PHYIDX 0
-#define CONFIG_ETHPRIME "MOTO ENET0"
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0"
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
projects / u-boot / blobdiff