Add GPL-2.0+ SPDX-License-Identifier to source files

[u-boot] / include / configs / MPC8568MDS.h

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 3674e495c5c23997b90fa06ac312c66e6d238d52..21ce7b9125afe1c3b5ea199760e90c4f51d7fcea 100644 (file)
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -1,23 +1,7 @@
 /*
  * Copyright 2004-2007, 2010-2011 Freescale Semiconductor.
  *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.         See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier:    GPL-2.0+ 
  */
 
 /*
@@ -42,6 +26,7 @@
 #define CONFIG_PCI1            1       /* PCI controller */
 #define CONFIG_PCIE1           1       /* PCIE controller */
 #define CONFIG_FSL_PCI_INIT    1       /* use common fsl pci init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
@@ -71,14 +56,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xe0000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
@@ -261,7 +240,6 @@ extern unsigned long get_clock_freq(void);
 /* Use the HUSH parser*/
 #define CONFIG_SYS_HUSH_PARSER
 #ifdef  CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* pass open firmware flat tree */
@@ -334,7 +312,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16
 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 #endif
 
@@ -346,14 +324,13 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16
 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 #endif
 #endif /* CONFIG_QE */
 
 #if defined(CONFIG_PCI)
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -364,10 +341,6 @@ extern unsigned long get_clock_freq(void);
 
 #endif /* CONFIG_PCI */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_MII             1       /* MII PHY management */
@@ -451,11 +424,11 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
@@ -481,8 +454,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_IPADDR    192.168.1.253
 
 #define CONFIG_HOSTNAME  unknown
-#define CONFIG_ROOTPATH  /nfsroot
-#define CONFIG_BOOTFILE  your.uImage
+#define CONFIG_ROOTPATH  "/nfsroot"
+#define CONFIG_BOOTFILE  "your.uImage"
 
 #define CONFIG_SERVERIP  192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1