#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
-
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-
/*
* DDR Setup
*/
#endif
#if defined(CFG_RAMBOOT)
-#undef CFG_FLASH_CFI_DRIVER
#undef CONFIG_SPD_EEPROM
#define CFG_SDRAM_SIZE 256
#endif
/*
* I2C
*/
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3100
/*
* RapidIO MMU
#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
-
#if defined(CONFIG_PCI)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#endif /* CONFIG_PCI */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID 4
+#define CFG_SCSI_MAX_LUN 1
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#endif
+
+#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC86XX_TSEC1 1
-#define CONFIG_MPC86XX_TSEC1_NAME "eTSEC1"
-#define CONFIG_MPC86XX_TSEC2 1
-#define CONFIG_MPC86XX_TSEC2_NAME "eTSEC2"
-#define CONFIG_MPC86XX_TSEC3 1
-#define CONFIG_MPC86XX_TSEC3_NAME "eTSEC3"
-#define CONFIG_MPC86XX_TSEC4 1
-#define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4"
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "eTSEC4"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#endif /* CONFIG_TSEC_ENET */
-
/*
* BAT0 2G Cacheable, non-guarded
* 0x0000_0000 2G DDR
#define CFG_IBAT7L 0x00000000
#define CFG_IBAT7U 0x00000000
-
-
-
/*
* Environment
*/
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
#if defined(CFG_RAMBOOT)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_PCI \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_IMLS \
- | CFG_CMD_FLASH \
- | CFG_CMD_LOADS))
- #else
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_IMLS \
- | CFG_CMD_FLASH \
- | CFG_CMD_LOADS))
- #endif
-#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C)
- #else
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C)
- #endif
+ #undef CONFIG_CMD_ENV
+#endif
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+ #define CONFIG_CMD_SCSI
+ #define CONFIG_CMD_EXT2
#endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#if defined(CONFIG_CMD_KGDB)
+ #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#if defined(CONFIG_CMD_KGDB)
+ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-
/*
* Environment Configuration
*/
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /opt/nfsroot
#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
- "ramdiskaddr=400000\0" \
+ "ramdiskaddr=2000000\0" \
"ramdiskfile=your.ramdisk.u-boot\0" \
- "pex0=echo ---------------------------; echo --------- PCI EXPRESS -----\0"\
- "pexstat=mw f8008000 84000004; echo -expect:- 16000000; md f8008004 1\0" \
- "pex1=pci write 1.0.0 4 146; pci write 1.0.0 10 80000000\0" \
- "pexd=echo -expect:- xxx01002 00100146; pci display 1.0.0 0 2\0" \
- "pex=run pexstat; run pex1; run pexd\0" \
+ "dtbaddr=c00000\0" \
+ "dtbfile=mpc8641_hpcn.dtb\0" \
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
"maxcpus=2"
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr - $dtbaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
projects / u-boot / blobdiff