ARM: versatile: pass console setting to the kernel

[u-boot] / include / configs / P1010RDB.h

diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index c6b9acac3bad17373533e7fdd1ff7d85df5b221c..ea5cb6501b6f4ec32d01228980f8b544bc1b32cd 100644 (file)
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -37,7 +37,7 @@
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
 
@@ -173,12 +173,12 @@
 #define CONFIG_SYS_NUM_ADDR_MAP                16      /* number of TLB1 entries */
 #endif
 
-#define CONFIG_SYS_MEMTEST_START       0x00000000      /* memtest works on */
+#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x1fffffff
 #define CONFIG_PANIC_HANG              /* do not reset board on panic */
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM         1
@@ -313,6 +313,13 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_NAND_BASE_PHYS      CONFIG_SYS_NAND_BASE
 #endif
 
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITION
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT                 "nand0=ff800000.flash"
+#define MTDPARTS_DEFAULT               \
+       "mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
+
 #define CONFIG_SYS_NAND_CSPR   (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                                | CSPR_PORT_SIZE_8      \
                                | CSPR_MSEL_NAND        \
@@ -703,7 +710,6 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
 #define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
@@ -714,7 +720,6 @@ extern unsigned long get_sdram_size(void);
                                                /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ          1000            /* dec freq: 1ms ticks */
 
 /*
  * Internal Definitions
@@ -734,7 +739,6 @@ extern unsigned long get_sdram_size(void);
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 /*