/*
- * Copyright 2009 Freescale Semiconductor, Inc.
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#ifdef CONFIG_NAND
#define CONFIG_NAND_U_BOOT 1
#define CONFIG_RAMBOOT_NAND 1
-#define CONFIG_RAMBOOT_TEXT_BASE 0xf8f82000
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
+#else
+#define CONFIG_SYS_TEXT_BASE 0xf8f82000
+#endif /* CONFIG_NAND_SPL */
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD 1
-#define CONFIG_RAMBOOT_TEXT_BASE 0xf8f80000
+#define CONFIG_SYS_TEXT_BASE 0xf8f80000
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH 1
-#define CONFIG_RAMBOOT_TEXT_BASE 0xf8f80000
+#define CONFIG_SYS_TEXT_BASE 0xf8f80000
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
/* High Level Configuration Options */
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_DLL
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND) \
- || defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH)
+#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \
+ defined(CONFIG_RAMBOOT_SPIFLASH)
#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
#else
#undef CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \
- - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
+ - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
#define CONFIG_SYS_EEPROM_BUS_NUM 1
#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_RTC_DS1337_NOOSC
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/*
* General PCI
*/
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME "Slot 1"
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "Slot 2"
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-/* TBI PHY configuration for SGMII mode */
-#define CONFIG_TSEC_TBICR_SETTINGS ( \
- TBICR_PHY_RESET \
- | TBICR_ANEG_ENABLE \
- | TBICR_FULL_DUPLEX \
- | TBICR_SPEED1_SET \
- )
-
#endif /* CONFIG_TSEC_ENET */
/*
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (16 << 20)/* Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */