do_bootd: unify duplicate prototypes

[u-boot] / include / configs / P2020DS.h

diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index 27e8d8edb05e54b55ab5c45e9649897c09f153a8..0af21528d9a82345bc132825cd85e1108dc1f445 100644 (file)
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -41,6 +41,10 @@
 #define CONFIG_P2020DS         1
 #define CONFIG_MP              1       /* support multiple processors */
 
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xeff80000
+#endif
+
 #define CONFIG_FSL_ELBC                1       /* Has Enhanced localbus controller */
 #define CONFIG_PCI             1       /* Enable PCI/PCIE */
 #define CONFIG_PCIE1           1       /* PCIE controler 1 (slot 1) */
@@ -73,8 +77,9 @@
 #define CONFIG_SYS_NUM_ADDR_MAP                16      /* number of TLB1 entries */
 #endif
 
-#define CONFIG_SYS_MEMTEST_START       0x00000000      /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END         0x7fffffff
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY     /* test POST memory test */
+#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END         0x00400000
 #define CONFIG_PANIC_HANG      /* do not reset board on panic */
 
 /*
@@ -267,10 +272,9 @@
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 #endif
-#define CONFIG_SYS_INIT_RAM_END        0x00004000      /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       0x00004000      /* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (256 * 1024) /* Reserve 256 kB for Mon */
@@ -605,14 +609,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02            /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */