Merge branch 'master' of git://git.denx.de/u-boot-nand-flash

[u-boot] / include / configs / P2020DS.h

diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index 99555012f837adfa0c202c9a821ed99c3949b50a..102e4c96f2d8278f9ef9e636daea99376db05661 100644 (file)
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -29,7 +29,7 @@
 
 #include "../board/freescale/common/ics307_clk.h"
 
-#ifdef CONFIG_MK_36BIT
+#ifdef CONFIG_36BIT
 #define CONFIG_PHYS_64BIT
 #endif
 
@@ -41,6 +41,10 @@
 #define CONFIG_P2020DS         1
 #define CONFIG_MP              1       /* support multiple processors */
 
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xeff80000
+#endif
+
 #define CONFIG_FSL_ELBC                1       /* Has Enhanced localbus controller */
 #define CONFIG_PCI             1       /* Enable PCI/PCIE */
 #define CONFIG_PCIE1           1       /* PCIE controler 1 (slot 1) */
@@ -90,13 +94,13 @@
 #endif
 #define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
-#define CONFIG_SYS_PCIE3_ADDR          (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE2_ADDR          (CONFIG_SYS_CCSRBAR+0x9000)
-#define CONFIG_SYS_PCIE1_ADDR          (CONFIG_SYS_CCSRBAR+0xa000)
-
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
+#ifdef CONFIG_DDR2
+#define CONFIG_FSL_DDR2
+#else
 #define CONFIG_FSL_DDR3                1
+#endif
 #undef CONFIG_FSL_DDR_INTERACTIVE
 
 /* ECC will be enabled based on perf_mode environment variable */
@@ -113,6 +117,7 @@
 #define CONFIG_CHIP_SELECTS_PER_CTRL   2
 
 /* I2C addresses of SPD EEPROMs */
+#define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM         0       /* SPD EEPROM located on I2C bus 0 */
 #define SPD_EEPROM_ADDRESS1    0x51    /* CTLR 0 DIMM 0 */
 
@@ -223,7 +228,7 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT    60000           /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT    500             /* Flash Write Timeout (ms) */
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -232,6 +237,7 @@
 
 #define CONFIG_BOARD_EARLY_INIT_R      /* call board_early_init_r function */
 
+#define CONFIG_HWCONFIG                        /* enable hwconfig */
 #define CONFIG_FSL_NGPIXIS             /* use common ngPIXIS code */
 
 #ifdef CONFIG_FSL_NGPIXIS
@@ -253,6 +259,18 @@
 
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xffd00000      /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+       ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS  CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
 #define CONFIG_SYS_INIT_RAM_END        0x00004000      /* End of used area in RAM */
 
 #define CONFIG_SYS_GBL_DATA_SIZE       128     /* num bytes initial data */
@@ -323,7 +341,6 @@
  * shorted - index 1
  */
 #define CONFIG_CONS_INDEX      1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -547,6 +564,7 @@
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
@@ -570,7 +588,8 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING         /* Command-line editing */
+#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -644,11 +663,11 @@
  "netdev=eth0\0"                                               \
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                                \
  "tftpflash=tftpboot $loadaddr $uboot; "                       \
-       "protect off " MK_STR(TEXT_BASE) " +$filesize; "        \
-       "erase " MK_STR(TEXT_BASE) " +$filesize; "              \
-       "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "      \
-       "protect on " MK_STR(TEXT_BASE) " +$filesize; "         \
-       "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"     \
+       "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "     \
+       "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "           \
+       "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "   \
+       "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "              \
+       "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"  \
  "consoledev=ttyS0\0"                          \
  "ramdiskaddr=2000000\0"                       \
  "ramdiskfile=p2020ds/ramdisk.uboot\0"         \