Move CONFIG_PANIC_HANG to Kconfig

[u-boot] / include / configs / T104xRDB.h

diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index d2ece40d4ac34ddf9888931df4b003d83394fa3d..ceb9daaac2ea9bffbb7db09035388795aaca2b9e 100644 (file)
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -180,13 +180,11 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 
 #if defined(CONFIG_SPIFLASH)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
 #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
 #define CONFIG_ENV_SECT_SIZE            0x10000
 #elif defined(CONFIG_SDCARD)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV          0
 #define CONFIG_ENV_SIZE                        0x2000
 #define CONFIG_ENV_OFFSET              (512 * 0x800)
@@ -196,11 +194,9 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #define CONFIG_BOOTSCRIPT_COPY_RAM
 #endif
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE                        0x2000
 #define CONFIG_ENV_OFFSET              (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
@@ -230,7 +226,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
 #define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG      /* do not reset board on panic */
 
 /*
  *  Config the L3 Cache as L3 SRAM
@@ -401,7 +396,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (512 * 1024)
 
@@ -619,16 +613,12 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 /* SATA */
 #define CONFIG_FSL_SATA_V2
 #ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
 #define CONFIG_SYS_SATA_MAX_DEVICE     1
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1               CONFIG_SYS_MPC85xx_SATA1_ADDR
 #define CONFIG_SYS_SATA1_FLAGS         FLAGS_DMA
 
 #define CONFIG_LBA48
-#define CONFIG_CMD_SATA
 #endif
 
 /*
@@ -640,6 +630,7 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_EHCI_DESC_BIG_ENDIAN
 #endif
 #endif
 
@@ -748,7 +739,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 /* Enable VSC9953 L2 Switch driver on T1040 SoC */
 #if defined(CONFIG_TARGET_T1040RDB) || defined(CONFIG_TARGET_T1040D4RDB)
 #define CONFIG_VSC9953
-#define CONFIG_CMD_ETHSW
 #ifdef CONFIG_TARGET_T1040RDB
 #define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR       0x04
 #define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR       0x08
@@ -760,7 +750,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 
 #define CONFIG_MII             /* MII PHY management */
 #define CONFIG_ETHPRIME                "FM1@DTSEC4"
-#define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
 #endif
 
 /*
@@ -769,23 +758,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #define CONFIG_LOADS_ECHO              /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
 
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
-
 /*
  * Miscellaneous configurable options
  */
@@ -793,14 +765,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
 #define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS     16              /* max number of command args */
-#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data
@@ -820,15 +784,7 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
 #ifdef CONFIG_MTD_NOR_FLASH
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
-                       "spi0=spife110000.0"
-#define MTDPARTS_DEFAULT       "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
-                               "128k(dtb),96m(fs),-(user);"\
-                               "fff800000.flash:2m(uboot),9m(kernel),"\
-                               "128k(dtb),96m(fs),-(user);spife110000.0:" \
-                               "2m(uboot),9m(kernel),128k(dtb),-(user)"
 #endif
 
 /*