#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Serial console configuration
*/
#define CONFIG_NS8382X 1
#endif /* CONFIG_STK52XX */
-#ifdef CONFIG_PCI
-#define ADD_PCI_CMD CFG_CMD_PCI
-#else
-#define ADD_PCI_CMD 0
-#endif
-
/*
* Video console
*/
#define CFG_CONSOLE_IS_IN_ENV
#endif /* #ifndef CONFIG_TQM5200S */
-#ifdef CONFIG_VIDEO
-#define ADD_BMP_CMD CFG_CMD_BMP
-#else
-#define ADD_BMP_CMD 0
-#endif
/* Partitions */
#define CONFIG_MAC_PARTITION
/* USB */
#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
#define CONFIG_USB_OHCI_NEW
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define CFG_OHCI_BE_CONTROLLER
#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
#undef CFG_USB_OHCI_BOARD_INIT
#define CFG_USB_OHCI_CPU_INIT
#define CFG_USB_OHCI_SLOT_NAME "mpc5200"
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
-#else
-#define ADD_USB_CMD 0
#endif
#ifndef CONFIG_CAM5200
#endif
#ifdef CONFIG_POST
-#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
/* preserve space for the post_word at end of on-chip SRAM */
#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#else
-#define CFG_CMD_POST_DIAG 0
#endif
-/* IDE */
-#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX) || defined(CONFIG_FO300)
-#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
-#else
-#define ADD_IDE_CMD 0
-#endif
/*
- * Supported commands
+ * BOOTP options
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- ADD_BMP_CMD | \
- ADD_IDE_CMD | \
- ADD_PCI_CMD | \
- ADD_USB_CMD | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_NFS | \
- CFG_CMD_PING | \
- CFG_CMD_POST_DIAG | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SNTP | \
- CFG_CMD_BSP)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_BSP
+
+#ifdef CONFIG_VIDEO
+ #define CONFIG_CMD_BMP
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
+ #define CONFIG_CMD_IDE
+ #define CONFIG_CMD_FAT
+ #define CONFIG_CMD_EXT2
+#endif
+
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
+ #define CONFIG_CFG_USB
+ #define CONFIG_CFG_FAT
+#endif
+
+#ifdef CONFIG_POST
+ #define CONFIG_CMD_DIAG
+#endif
+
#define CONFIG_TIMESTAMP /* display image timestamps */
"protect on FC000000 +${filesize}\0"
#endif
-#ifndef CONFIG_CAM5200
+#if defined(CONFIG_TQM5200)
#define CUSTOM_ENV_SETTINGS \
+ "hostname=tqm5200\0" \
"bootfile=/tftpboot/tqm5200/uImage\0" \
+ "fdt_file=/tftpboot/tqm5200/tqm5200.dtb\0" \
"u-boot=/tftpboot/tqm5200/u-boot.bin\0"
-#else
-#define CUSTOM_ENV_SETTINGS \
+#elif defined(CONFIG_CAM5200)
+#define CUSTOM_ENV_SETTINGS \
"bootfile=cam5200/uImage\0" \
"u-boot=cam5200/u-boot.bin\0" \
"setup=tftp 200000 cam5200/setup.img; autoscr 200000\0"
#endif
+#if defined(CONFIG_TQM5200_B)
+#define ENV_FLASH_LAYOUT \
+ "fdt_addr=FC100000\0" \
+ "kernel_addr=FC140000\0" \
+ "ramdisk_addr=FC600000\0"
+#else /* !CONFIG_TQM5200_B */
+#define ENV_FLASH_LAYOUT \
+ "fdt_addr=FC0A0000\0" \
+ "kernel_addr=FC0C0000\0" \
+ "ramdisk_addr=FC300000\0"
+#endif
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
+ "console=ttyPSC0\0" \
+ ENV_FLASH_LAYOUT \
+ "kernel_addr_r=400000\0" \
+ "fdt_addr_r=600000\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addcons=setenv bootargs ${bootargs} " \
- "console=ttyS0,${baudrate}\0" \
- "flash_self=run ramargs addip addcons;" \
+ "console=${console},${baudrate}\0" \
+ "flash_self_old=sete console ttyS0; run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
+ "flash_self=run ramargs addip addcons;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs_old=sete console ttyS0; run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
- "bootm\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
+ "sete console ttyS0; run nfsargs addip addcons;bootm\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
+ "tftp ${fdt_addr_r} ${fdt_file}; " \
+ "run nfsargs addip addcons; " \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
CUSTOM_ENV_SETTINGS \
"load=tftp 200000 ${u-boot}\0" \
ENV_UPDT \
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133) && !defined(CONFIG_CAM5200)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK) && !defined(CONFIG_CAM5200)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock of
+ * 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
# if defined(CONFIG_TQM5200_B)
# if defined(CFG_LOWBOOT)
# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:1m(firmware)," \
- "1536k(kernel)," \
- "3584k(small-fs)," \
+ "256k(dtb)," \
+ "2304k(kernel)," \
+ "2560k(small-fs)," \
"2m(initrd)," \
"8m(misc)," \
"16m(big-fs)"
# endif /* CFG_LOWBOOT */
# else /* !CONFIG_TQM5200_B */
# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
- "1408k(kernel)," \
+ "128k(dtb)," \
+ "2304k(kernel)," \
"2m(initrd)," \
"4m(small-fs)," \
"8m(misc)," \
- "16m(big-fs)"
+ "15m(big-fs)"
# endif /* CONFIG_TQM5200_B */
#elif defined (CONFIG_CAM5200)
# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \
# if defined (CONFIG_TQM5200_REV100)
# error TQM5200 REV100 not supported on STK52XX REV200 or above
# else/* TQM5200 REV200 and above */
-# define CFG_GPS_PORT_CONFIG 0x91500004
+# define CFG_GPS_PORT_CONFIG 0x91500404
# endif
# endif
#elif defined (CONFIG_FO300)
#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
#define CFG_PROMPT_HUSH_PS2 "> "
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
- * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
- * which is normally part of the default commands (CFV_CMD_DFL)
+ * Enable loopw command.
*/
#define CONFIG_LOOPW
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/* Interval between registers */
#define CFG_ATA_STRIDE 4
+/*-----------------------------------------------------------------------
+ * Open firmware flat tree support
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
#endif /* __CONFIG_H */
projects / u-boot / blobdiff