board configs: drop NET_MULTI references

[u-boot] / include / configs / aev.h

diff --git a/include/configs/aev.h b/include/configs/aev.h
index 98958a6237bbe42bf76afe6650d2083c44e01b66..8d0890fc8adad997d755d5cd83b6763e6e790cdc 100644 (file)
--- a/include/configs/aev.h
+++ b/include/configs/aev.h
@@ -41,10 +41,18 @@
 #define CONFIG_AEVFIFO         1
 #define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33.000000MHz */
 
-#define CONFIG_HIGH_BATS       1       /* High BATs supported */
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFC000000  boot low (standard configuration with room for
+ *             max 64 MByte Flash ROM)
+ * 0xFFF00000  boot high (for a backup copy of U-Boot)
+ * 0x00100000  boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xFC000000
+#endif
 
-#define BOOTFLAG_COLD          0x01    /* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM          0x02    /* Software reboot           */
+#define CONFIG_HIGH_BATS       1       /* High BATs supported */
 
 /*
  * Serial console configuration
@@ -72,7 +80,6 @@
 #define CONFIG_PCI_IO_PHYS     CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE     0x01000000
 
-#define CONFIG_NET_MULTI       1
 #define CONFIG_EEPRO100                1
 #define CONFIG_SYS_RX_ETH_BUFFER       8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X         1
@@ -128,7 +135,7 @@
 
 #define        CONFIG_TIMESTAMP                /* display image timestamps */
 
-#if (TEXT_BASE == 0xFC000000)          /* Boot low */
+#if (CONFIG_SYS_TEXT_BASE == 0xFC000000)               /* Boot low */
 #   define CONFIG_SYS_LOWBOOT          1
 #endif
 
@@ -221,7 +228,7 @@
 /*
  * Flash configuration
  */
-#define CONFIG_SYS_FLASH_BASE          TEXT_BASE /* 0xFC000000 */
+#define CONFIG_SYS_FLASH_BASE          CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
 
 /* use CFI flash driver if no module variant is spezified */
 #define CONFIG_SYS_FLASH_CFI           1       /* Flash is CFI conformant */
@@ -263,17 +270,16 @@
 #define CONFIG_SYS_INIT_RAM_ADDR       MPC5XXX_SRAM
 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_POST_SIZE
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_POST_SIZE
 #else
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_SIZE
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_SIZE
 #endif
 
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT          1
 #endif
@@ -286,10 +292,11 @@
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC     1
+#define CONFIG_MPC5xxx_FEC_MII100
 /*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
  */
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
 #define CONFIG_PHY_ADDR                0x00
 
 /*