microblaze: Enable TFTP put command

[u-boot] / include / configs / davinci_sonata.h

diff --git a/include/configs/davinci_sonata.h b/include/configs/davinci_sonata.h
index 0dc89ef41e2c2b329105c255a323ced809380843..854099b2a26f500b353eb4fac961e0a96a1b564c 100644 (file)
--- a/include/configs/davinci_sonata.h
+++ b/include/configs/davinci_sonata.h
@@ -51,7 +51,8 @@
 #define SONATA_BOARD
 #define CONFIG_SYS_NAND_SMALLPAGE
 #define CONFIG_SYS_USE_NOR
-#define CONFIG_DISPLAY_CPUINFO
+#define MACH_TYPE_SONATA 1254
+#define CONFIG_MACH_TYPE MACH_TYPE_SONATA
 /*===================*/
 /* SoC Configuration */
 /*===================*/
@@ -101,14 +102,12 @@
 /* Network & Ethernet Configuration */
 /*==================================*/
 #define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_EMAC_MDIO_PHY_NUM       1
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT 10
-#define CONFIG_NET_MULTI
 /*=====================*/
 /* Flash & Environment */
 /*=====================*/
@@ -126,7 +125,6 @@
 #define CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices */
 #define CONFIG_ENV_OFFSET              0x0     /* Block 0--not used by bootcode */
-#define DEF_BOOTM              ""
 #elif defined(CONFIG_SYS_USE_NOR)
 #ifdef CONFIG_NOR_UART_BOOT
 #define CONFIG_SKIP_LOWLEVEL_INIT      /* U-Boot is loaded by a bootloader */
@@ -140,6 +138,7 @@
 #define CONFIG_SYS_MAX_FLASH_BANKS     1               /* max number of flash banks */
 #define CONFIG_SYS_FLASH_SECT_SZ       0x20000         /* 128KB sect size AMD Flash */
 #define CONFIG_ENV_OFFSET              (CONFIG_SYS_FLASH_SECT_SZ*2)
+#define CONFIG_ENV_SIZE                CONFIG_SYS_FLASH_SECT_SZ
 #define PHYS_FLASH_1           0x02000000      /* CS2 Base address      */
 #define CONFIG_SYS_FLASH_BASE          PHYS_FLASH_1    /* Flash Base for U-Boot */
 #define PHYS_FLASH_SIZE                0x2000000       /* Flash size 32MB       */
@@ -199,11 +198,17 @@
 #else
 #error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
 #endif
-/*=======================*/
-/* KGDB support (if any) */
-/*=======================*/
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE   115200  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  1       /* which serial port to use */
+
+#ifdef CONFIG_CMD_BDI
+#define CONFIG_CLOCKS
 #endif
+
+#define CONFIG_MAX_RAM_BANK_SIZE       (256 << 20)     /* 256 MB */
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000
+#define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_SDRAM_BASE + \
+                                        CONFIG_SYS_INIT_RAM_SIZE - \
+                                        GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */