fsl: refactor MPC8610 and MPC5121 DIU code to use existing bitmap and logo features

[u-boot] / include / configs / edminiv2.h

diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index c3d95a04c43549c65c949c8fea7c41756e529a6a..ccfc66053b5627553ccd9730b67ae949a37430b3 100644 (file)
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -60,7 +60,7 @@
 
 #define ORION5X_MPP0_7         0x00000003
 #define ORION5X_MPP8_15                0x55550000
-#define ORION5X_MPP16_23       0x00000000
+#define ORION5X_MPP16_23       0x00005555
 
 /*
  * Board-specific values for Orion5x GPIO low level init:
@@ -131,12 +131,66 @@
  * Commands configuration - using default command set for now
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_I2C
+
+/*
+ * Network
+ */
+
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE                           /* Enable Marvell GbE Driver */
+#define CONFIG_MVGBE_PORTS     {1}             /* enable port 0 only */
+#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION    /* don't randomize MAC */
+#define CONFIG_PHY_BASE_ADR    0x8
+#define CONFIG_RESET_PHY_R     /* use reset_phy() to init mv8831116 PHY */
+#define CONFIG_NETCONSOLE      /* include NetConsole support   */
+#define CONFIG_NET_MULTI       /* specify more that one ports available */
+#define        CONFIG_MII              /* expose smi ove miiphy interface */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN        /* detect link using phy */
+#define CONFIG_ENV_OVERWRITE   /* ethaddr can be reprogrammed */
+#endif
+
+/*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET     (0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET      (0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET      (0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE          4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS          1
+#define CONFIG_SYS_IDE_MAXDEVICE       1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR       ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET     ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
 /*
- * Disabling some default commands for staggered bring-up
+ * I2C related stuff
  */
-#undef CONFIG_CMD_BOOTD        /* no bootd since no net */
-#undef CONFIG_CMD_NET  /* no net since no eth */
-#undef CONFIG_CMD_NFS  /* no NFS since no net */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE         ORION5X_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE           0x0
+#define CONFIG_SYS_I2C_SPEED           100000
+#endif
 
 /*
  *  Environment variables configurations